From: Brad Hedlund (BHedlund@xxxxxxxxxxxxxxxxxxx)
Date: Sun Feb 06 2000 - 15:06:48 GMT-3
I wasnt implying that the vty ports dont need to be configured. Of course,
if your asked to configure them in the test then configure them.
But if not asked to, or it isnt a stated requirement, then dont. Thats what
I meant to say.
Time is of the essence, the pre-config on each router after first connecting
to it via comm-server should have the basics to get you moving along to your
next tasks.
Of course, thats just my humble opinion. Which has taken a beating here as
of late.
I'll go home and lick my wounds.
host R#
no ip domain-lo
no logging con
ip clas
ip sub
line con 0
exec-t 0 0
That was my pre-config for each router.
That worked for me. You may find something else that works for you.
The proctor used the comm-server to grade my test. When I went back to my
station I scrolled up on Hyperterm to see what he checked.
Brad Hedlund
CCIE #5530
Network Guidance Company
> Au contrare mon frare (sic). Both times I did indeed
> need to config the vty ports for telnet. I assumed
> that the proctor used them for grading.
>
> J.
>
>
> --- Brad Hedlund <BHedlund@LifeTimeFitness.com> wrote:
> > Why do you need 'logg sync' when you have already
> > turned off logging with
> > 'no logging con'?
> >
> > Dont waste your time configuring the vty lines. They
> > are not used in the
> > lab. You console into each router via a term
> > server.
> >
> > 'no exec-timeout' is NOT a valid command ....
> > rather it would be
> > 'exec-timeout 0 0'
> >
> > 'ip classless' is very important! It tells the
> > router use supernetted
> > routes in the routing table, including the default
> > route.
> >
> > Brad Hedlund
> > CCIE #5530
> > Network Guidance Company
> >
> >
> > -----Original Message-----
> > From: Earl Aboytes [mailto:earl@linkline.com]
> > Sent: Friday, February 04, 2000 11:02 AM
> > To: ccielab@groupstudy.com
> > Subject: Lab shortcuts
> >
> >
> > Here is a collection of shortcuts that was started
> > on another list. Can any
> > of you add to the list?
> >
> > !Commserver
> > w = 'where' = 'show session' on comm server
> > connect to routers in order on Commserver. press 1
> > to connect to R1 and so
> > forth.
> > line 1 16
> > no exec
> > !prevents all that garbage from coming through when
> > you connect to router
> > consoles.
> >
> >
> > ! router timesavers
> > ip classless
> > ! Any good reason not to have this?
> > no ip domain-lookup
> > ! prevents mistakes from becoming DNS lookups
> > ip tcp syn 5
> > ! Reduces telnet timeout (default is 30 seconds)
> > no logg con
> > ! Eliminates console messages from popping up while
> > typing
> > line con 0
> > logging synchronous (or logg sync)
> > !This makes console messages a whole lot less
> > annoying. Instead of
> > !interrupting your input with a message, the router
> > will now issue the
> > !message, but repeat your input on the following
> > line with your cursor in
> > !the original position -- very handy.
> >
> >
> >
> > line con 0
> > no exec-timeout !Prevents console logout
> > privilege level 15 !Drops you in privilege EXEC mode
> > without typing enable
> > line vty 0 4
> > no exec-timeout !prevents telnet timeout
> > no login !no prompt for login
> > privilege level 15 !Drops you in privilege EXEC mode
> > without typing enable
> >
> > ! Catalyst timesavers
> > set logout 0 ! prevents console logout
> >
> >
> > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> > Earl Aboytes
> > Senior Technical Consultant
> > GTE-Managed Solutions
> > 800-483-5325 x8817
> > earl.aboytes@telops.gte.com
> > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:22:52 GMT-3