From: Frank K. Lu (fclu@xxxxxxxxxxxxx)
Date: Fri May 26 2000 - 19:36:52 GMT-3
I have tried your config in my lab, both R6 and R2 are "full" with R3 for at le
ast
15 minutes before I erase the config, and R3 is the DR as you expected.
May be you can try to clear the ospf process on both R3 and R6 see if that help
.
Thanks,
-Frank
Vijay Venkatesh wrote:
> Dude,
> You have a p-p and you are using ospf network-broadcast. On the int p
-p
> use ip ospf network point-to-multipoint and do the same on the ser 0
> interfaces. p-p interface with ospf network broadcast will not work.
> Simply use ip ospf network point-to-multipoint all over and router will
> be peaceful.
>
> Vijay.
>
> Rene Mendoza wrote:
> >
> > Have you tried the good old friend "debug ip ospf adj" ?
> >
> > "David H. Brown" wrote:
> >
> > > I have a type 1 question, the brick wall is getting dented by my hard hea
d.
> > > I am running CCBootCamp lab #7, still on step one of task 2. OSPF adj
> > > between R6 and R3 keeps going up and down, and it's driving me nuts! The
> > > debug on R3 shows the state going to FULL then back to INIT (round and
> > > round), and on R6 goes to FULL then DOWN and starts over. I will be
> > > thrilled to hear how I missed something very basic here, I just don't see
> > > it. BTW, R2-R3 works perfectly. Thanks!
> > >
> > > David
> > > (RTP Lab 6/15)
> > >
> > > All routers have IOS Version: (C2500-DS56-L), Version 11.2(22)
> > >
> > > ------ ------ ------
> > > |2503| |2510| |2513|
> > > ------ ------ ------
> > > R6 -- frame -- R3 -- frame -- R2
> > > S0 S0.1 -- S0.2 S0
> > >
> > > S3:
> > > interface Serial0
> > > no ip address
> > > encapsulation frame-relay
> > > !
> > > interface Serial0.1 point-to-point
> > > ip address 10.100.1.3 255.255.0.0
> > > ip ospf network broadcast
> > > ip ospf priority 100
> > > frame-relay interface-dlci 306
> > > !
> > > interface Serial0.2 point-to-point
> > > ip address 10.101.1.3 255.255.0.0
> > > ip ospf network broadcast
> > > ip ospf priority 100
> > > frame-relay interface-dlci 302
> > >
> > > router ospf 64
> > > network 10.101.1.3 0.0.0.0 area 0
> > > network 10.100.1.3 0.0.0.0 area 0
> > > !
> > > -----------------------------------
> > > S6:
> > > !
> > > interface Serial0
> > > ip address 10.100.1.6 255.255.0.0
> > > encapsulation frame-relay
> > > ip ospf network broadcast
> > > ip ospf priority 0
> > > frame-relay map ip 10.100.1.3 603 broadcast
> > > !
> > > router ospf 64
> > > network 10.100.1.6 0.0.0.0 area 0
> > > !
> > > -----------------------------------
> > > S2:
> > > !
> > > interface Serial0
> > > ip address 10.101.1.2 255.255.0.0
> > > encapsulation frame-relay
> > > ip ospf network broadcast
> > > ip ospf priority 0
> > > no fair-queue
> > > frame-relay map ip 10.101.1.3 203 broadcast
> > > !
> > > router ospf 64
> > > network 10.101.1.2 0.0.0.0 area 0
> > > !
> > > -----------------------------------
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:31 GMT-3