From: Kevin Baumgartner (kbaumgar@xxxxxxxxx)
Date: Tue Nov 07 2000 - 14:09:59 GMT-3
So why does RIPV2 need to be used on R1? With RIPV1 I think it will summarize t
he
172.16.10.0/24 network to a classful route of 172.16.0.0/16. Which will not be
propagated
across to R2 since it's not a /24 network now. So need to get the summarized 17
2.16.0.0
network to be /24. How does RIPV2 do this?
Kevin
At 09:02 AM 11/7/00 -0600, Sam Munzani wrote:
>So it would work for following drawing.
>172.16.10.0/24--(e0)R1(e1)----192.168.10.0/24----(e1)R2(e0)---192.168.20.0/2
>4
>
>The network from R1's E0 side can be summarized to /16 and it will work.
>
>Thanks,
>Sam
>
>
> > Configure R1 to run RIPv2 and send RIPv1 updates to R2. And the subnetwork
>between R1 and R2 should not be same as R1's e0. Remember that RIP will auto
>summurize at network boundary?
> >
> > Regards,
> > Wu
> >
> > ----- Original Message -----
> > From: Sam Munzani <sam@munzani.com>
> > To: Wu,Jiang <wujiang@bj163.com>; Daniel Keller <DMKeller@comdisco.com>
> > Cc: <ccielab@groupstudy.com>
> > Sent: Tuesday, November 07, 2000 10:39 PM
> > Subject: Re: RIP summary routes?
> >
> >
> > > But will it send summary route? Here is my ASCII drawing.
> > >
> > > 172.16.10.0/24--(e0)R1(e1)----172.16.20.0/24----(e1)R2(e0)---
> > >
> > > If R1 and R2 are using RIP1. and you use "ip summary-route 172.16.0.0
>mask
> > > 255.255.0.0" on E1 or R1, will it show up on R2? I tried and it doesn't.
> > > Because RIP1 doesn't have subnet mask in update so R1 will send out only
>/24
> > > networks to a /24 interface.
> > >
> > > If somebody have it working against the behavior of RIP1 please post
>configs
> > > and routing table.
> > >
> > > Sam
> > >
> > >
> > > > Set the router to send only RIPv1 updates, may need to apply a
> > > distribute-list.
> > > >
> > > > ----- Original Message -----
> > > > From: Daniel Keller <DMKeller@comdisco.com>
> > > > To: <ccielab@groupstudy.com>
> > > > Sent: Tuesday, November 07, 2000 10:20 AM
> > > > Subject: RIP summary routes?
> > > >
> > > >
> > > > >
> > > > > Is it possible to send a summary route to a neighbor? I have a
>practice
> > > lab that asks me to configure RIP to only unicast a summary route of
> > > 140.1.0.0 to a neighbor router. I have searced CCO and tried doing this
> > > with no luck. Is this even possible or is the author of the lab on
>drugs?
> > > > >
> > > > > DK
> > > > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:43 GMT-3