From: Greg Ferro (gferro@xxxxxxxxxxxxxxxxxxx)
Date: Tue Nov 14 2000 - 21:56:09 GMT-3
This is a snapshot of what I have done. You may have to interpret slightly.
These lines set the VPI to be 0 bits long, and VCI 12 bits.
#set inter 2 0 0 0 12
Line Interface 2 has been registered.
A100#set inter 4 0 0 0 12
Line Interface 4 has been registered.
A100#set inter 6 0 0 0 12
Line Interface 6 has been registered.
A100#set inter 8 0 0 0 12
Line Interface 8 has been registered.
A100#set inter 10 0 0 0 12
Line Interface 10 has been registered.
A100#set inter 12 0 0 0 12
Line Interface 12 has been registered.
These lines set up the PVC's on each interface for a full mesh.
pvc est 1 2 2 0 204 512 0 155 4 0 402 512 0 155
pvc est 1 2 2 0 206 512 0 155 6 0 602 512 0 155
pvc est 1 2 2 0 208 512 0 155 8 0 802 512 0 155
pvc est 1 2 2 0 210 512 0 155 10 0 1002 512 0 155
pvc est 1 2 2 0 212 512 0 155 12 0 1202 512 0 155
pvc est 1 2 4 0 406 512 0 155 6 0 604 512 0 155
pvc est 1 2 4 0 408 512 0 155 8 0 804 512 0 155
pvc est 1 2 4 0 410 512 0 155 10 0 1004 512 0 155
pvc est 1 2 4 0 412 512 0 155 12 0 1204 512 0 155
pvc est 1 2 6 0 608 512 0 155 8 0 806 512 0 155
pvc est 1 2 6 0 610 512 0 155 10 0 1006 512 0 155
pvc est 1 2 6 0 612 512 0 155 12 0 1206 512 0 155
pvc est 1 2 8 0 810 512 0 155 10 0 1008 512 0 155
pvc est 1 2 8 0 812 512 0 155 12 0 1012 512 0 155
pvc est 1 2 10 0 1012 512 0 155 12 0 1210 512 0 155
These lines set uo routing in the chassis to supprt SVC;s. These are the
addresses of my ATM routers.
route add 3901000000000000000000000000602F8751 nsap 4 0
route add 39010000000000000000000000006070CC0E nsap 2 0
router 9 39010000000000000000000000006070CC0EAA00
router 10 3901000000000000000000000000602F87517D00
atm3s3 3901000000000000000000000000602FBE452000
A100#pvc est 1 2 2 0 204 512 0 155 4 0 402 512 0 155
***Connection has been established.
Connection Type : Bi
Traffic Type : UBR-BE
Low Throughput : -
High Throughput : -
LowLine LowVPI LowVCI LowUP LowCO HiLine HiVPI HiVCI HiUP HiCO
2 0 204 512 Pass 4 0 402 512 Pass
A100#pvc add 2 0 204 4 0 402
***Specified Connection is uni/bi-directional.
A100#show pvc
***Number of parameter is illegal.
A100#show pvc 2
Bandwidth Available (Forward/Backward/Line Rate): 155.0 / 155.0 / 155.0 Mbps
Existing connections : 0 (Uni), 1 (Bi), 0 (Multipoint), 2 (Gateway)
LowLine LowVPI LowVCI HiLine HiVPI HiVCI TrfType CONNECTION
2 0 5 16 0 2 UBR-BE Gateway
2 0 16 16 0 3 UBR-BE Gateway
2 0 204 4 0 402 UBR-BE Bi
A100#show pvc 4
Bandwidth Available (Forward/Backward/Line Rate): 155.0 / 155.0 / 155.0 Mbps
Existing connections : 0 (Uni), 1 (Bi), 0 (Multipoint), 2 (Gateway)
LowLine LowVPI LowVCI HiLine HiVPI HiVCI TrfType CONNECTION
4 0 5 16 0 2 UBR-BE Gateway
4 0 16 16 0 3 UBR-BE Gateway
4 0 402 2 0 204 UBR-BE Bi
A100#
ls100#set mib "Greg Ferro" "Bne CCIE Lab"
MIB information has been set.
A100#set local ls100 10.19.195.191 255.255.255.0 4701
Local configuration data has been set.
At 09:55 AM 15/11/2000, you wrote:
>Hello,
>
>Has anyone found any LS100 sample configs for simple tasks like configuring
>pvcs between interfaces etc.. Any direction is appreciated.
>
>Curtis
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:25:45 GMT-3