From: Peter Puczko (ppuczko@xxxxxxxxxx)
Date: Fri Feb 09 2001 - 01:32:38 GMT-3
Do not mix frame relay behaviour and OSPF.
DLCIs are bound to the major interface s0 after you configure encapsulation
frame relay. If you want those DLCIs to be used on subinterface you have to
add those lines into configuration. They don't just migrate there
auto-magically.
Once you put them there and verify IP connectivity you can start thinking
about OSPF part of it.
Peter
On Thu, 08 Feb 2001 23:22:28 -0500, Steven Weber wrote:
> If you do that then you need ip ospf network command and we are trying to
avoid
> that
>
> Peter Puczko wrote:
>
> > Where are your "frame-relay interface-dlci xxx" commands under s0.1?
> >
> > Peter
> >
> > On Thu, 08 Feb 2001 22:53:58 -0500, Steven Weber wrote:
> >
> > > I'm having some problems with my config I can't get any of the
spokes to
> > > ping each other any suggestions.Current configuration:
> > > !
> > > version 11.2
> > > !
> > > hostname r1
> > > !
> > > !
> > > no ip domain-lookup
> > > ip host r2 2001 10.1.1.100
> > > ip host r3 2002 10.1.1.100
> > > ip host r4 2003 10.1.1.100
> > > ip host r5 2004 10.1.1.100
> > > ip host r7 2006 10.1.1.100
> > > !
> > > interface Loopback0
> > > ip address 10.1.1.100 255.255.255.0
> > > !
> > > interface Ethernet0
> > > ip address 10.100.100.1 255.255.0.0
> > > no keepalive
> > > !
> > > interface Serial0
> > > no ip address
> > > encapsulation frame-relay
> > > ip ospf priority 10
> > > !
> > > interface Serial0.1 multipoint
> > > ip address 10.10.1.1 255.255.0.0
> > > ip policy route-map FRAM
> > > frame-relay map ip 10.10.1.2 102
> > > frame-relay map ip 10.10.1.3 103
> > > frame-relay map ip 10.10.1.5 105
> > > !
> > > interface Serial1
> > > no ip address
> > > shutdown
> > > !
> > > router ospf 1
> > > network 10.10.0.0 0.0.255.255 area 0
> > > network 10.100.0.0 0.0.255.255 area 1
> > > neighbor 10.10.1.3 priority 1
> > > neighbor 10.10.1.2 priority 1
> > > neighbor 10.10.1.5 priority 1
> > > !
> > > ip classless
> > > access-list 100 permit ip any 10.10.0.0 0.0.255.255
> > > access-list 101 permit ip any 10.10.0.0 0.0.255.255
> > > access-list 102 permit ip any 10.10.0.0 0.0.255.255
> > > route-map FRAM permit 10
> > > match ip address 100
> > > set ip next-hop 10.10.1.2
> > > !
> > > route-map FRAM permit 20
> > > match ip address 101
> > > set ip next-hop 10.10.1.3
> > > !
> > > route-map FRAM permit 30
> > > match ip address 102
> > > set ip next-hop 10.10.1.5
> > > !
> > > !
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:28:42 GMT-3