From: Haohong Lin (hhlin@xxxxxxxxxx)
Date: Fri May 04 2001 - 23:22:53 GMT-3
Hi,
I assume that there's catos bugs. I reset cat5k switch and the static
cam entries disappear. Maybe the most powerful weapeon is reload the boxes,
I think.
regards,
Haohong Lin
-----Original Message-----
From: tom cheung [mailto:tkc9789@hotmail.com]
Sent: 2001 05 05 10:03
To: hhlin@szskzj.com
Subject: RE: How to delete CAM entries marked 'Port Security Entry'
The command is "set port security x/y DISABLE". I tested on my cat5 and
works fine.
>From: "Haohong Lin" <hhlin@szskzj.com>
>To: "tom cheung" <tkc9789@hotmail.com>
>Subject: RE: How to delete CAM entries marked 'Port Security Entry'
>Date: Sat, 5 May 2001 07:48:58 +0800
>
>Hi,
>
> all the commands take no effect.
>
>Cat5509> en
>
>Enter password:
>Cat5K> (enable) sh port sec 2/17
>
>Port Security Secure-Src-Addr Last-Src-Addr Shutdown Trap
>IfIndex
>----- -------- ----------------- ----------------- -------- --------
>-------
> 2/17 disabled No enabled 26
>Cat5K> (enable) sh port stat 2/17
>Port Name Status Vlan Level Duplex Speed Type
>----- ------------------ ---------- ---------- ------ ------ -----
>---------
>---
> 2/17 R2522-250 connected 1 normal a-half a-10
>10/100BaseTX
>Cat5K> (enable) clear cam stat 1
>Static CAM entries cleared.
>Cat5509> (enable) sh cam stat
>* = Static Entry. + = Permanent Entry. # = System Entry. R = Router Entry.
>X = Port Security Entry
>
>VLAN Dest MAC/Route Des [CoS] Destination Ports or VCs / [Protocol
>Type]
>---- ------------------ -----
>-----------------------------------------
>--
>1 00-08-ca-fe-ca-fe X 2/17
>1 00-10-7b-3a-26-ee X 2/17
>Total Matching CAM Entries Displayed = 2
>Cat5K> (enable)
>
>
>Regards,
>
>Haohong Lin
>
>
>-----Original Message-----
>From: tom cheung [mailto:tkc9789@hotmail.com]
>Sent: 2001 05 04 19:53
>To: hhlin@szskzj.com; ccielab@groupstudy.com
>Subject: Re: How to delete CAM entries marked 'Port Security Entry'
>
>
>
>set port security 2/17 disable
>
>
> >From: "Haohong Lin" <hhlin@szskzj.com>
> >Reply-To: "Haohong Lin" <hhlin@szskzj.com>
> >To: "CCIELab" <ccielab@groupstudy.com>
> >Subject: How to delete CAM entries marked 'Port Security Entry'
> >Date: Fri, 4 May 2001 16:04:14 +0800
> >
> >Hi,
> >
> > I can't delete some static entries in cam table, as show in
>following.
> >I
> >find no command corelatively via show conf all .
> > I have pressed "set arp" command before, which maybe results in such
> >situation. After entered with "set arp ...", no commands are correlating
> >with it in nvram config.
> >
> > Any advice is welcome, thanks in advance
> >
> >Cat5k> (enable) sh cam stat
> >* = Static Entry. + = Permanent Entry. # = System Entry. R = Router
>Entry.
> >X = Port Security Entry
> >
> >VLAN Dest MAC/Route Des [CoS] Destination Ports or VCs / [Protocol
> >Type]
> >---- ------------------ -----
> >-----------------------------------------
> >--
> >1 00-08-ca-fe-ca-fe X 2/17
> >1 00-10-7b-3a-26-ee X 2/17
> >Total Matching CAM Entries Displayed = 2
> >Cat5k> (enable)
> >
> >
> >
> >regards,
> >
> >Haohong Lin
> >**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:30:34 GMT-3