From: Steven Weber (itweber@xxxxxxxxxxxxx)
Date: Sun Aug 26 2001 - 15:10:51 GMT-3
   
----- Original Message -----
From: Bob Chahal <bob.chahal@ntlworld.com>
To: rsevier <rsevier@zealousolutions.com>; <ccielab@groupstudy.com>
Sent: Sunday, August 26, 2001 1:45 PM
Subject: Re: redistributing IPX floating static
> Yep, its a typo, sorry.
>
> R3 is connected via frame-relay to R5.  On R3 I create a static route
>
> ipx route 12345670 FFFFFFFC 200.0000.0000.0001
>
> and then do
>
> ipx router eigrp 1
> redistribute static
>
> when a do a show run the "redistribute static" is not in the config and
the
> route does not appear in the ipx routing table on R5
>
> R3 config
> interface FastEthernet0/0
>   ipx network 200
>  ipx output-gns-filter 1000
>  ipx gns-reply-disable
> !
> interface Serial0/0
>   ipx network 5130
>  frame-relay map ipx 5130.0000.2222.0000 225
>  frame-relay map ipx 5130.0000.3333.0000 225
>  frame-relay map ipx 5130.0000.5555.0000 225 broadcast
>  no frame-relay inverse-arp
> !
> !
> ipx route 12345670 FFFFFFFC 200.0000.0000.0001
> !
> ipx router eigrp 1
>  network 5130
> !
> !
> ipx router rip
>  no network 5130
> !
>
> R5 IPX routing table
> 20 Total IPX routes. Up to 1 parallel paths and 16 hops allowed.
>
> Current default route is:
>
> E   FFFFFFFE [266521600/2] via      695.0000.0c3e.7424, age 00:15:27,
>                          1u, Et0
>
> SA       800 FFFFFFFC [**/**] via     6005.0000.6666.0000,        Di0
> C        695 (NOVELL-ETHER),  Et0
> C        700 (NOVELL-ETHER),  BV1
> C       5004 (FRAME-RELAY),   Se0.2
> C       5130 (FRAME-RELAY),   Se0.1
> C       6005 (PPP),           Di0
> E        200 [2172416/1] via     5130.0000.2222.0000, age 00:13:55,
>                          1u, Se0.1
> E        300 [2185984/1] via     5130.0000.3333.0000, age 00:15:09,
>                          1u, Se0.1
> E        400 [2172416/1] via     5004.0000.4444.0000, age 00:13:58,
>                          1u, Se0.2
> E        800 [267929600/2] via      695.0000.0c3e.7424, age 00:15:09,
>                          1u, Et0
> E        801 [267929600/2] via      695.0000.0c3e.7424, age 00:15:09,
>                          1u, Et0
> E        802 [267929600/2] via      695.0000.0c3e.7424, age 00:15:09,
>                          1u, Et0
> E        803 [267929600/2] via      695.0000.0c3e.7424, age 00:15:09,
>                          1u, Et0
> E   66666666 [45867776/1] via      695.0000.0c3e.7424, age 00:15:29,
>                          51u, Et0
> E   88888888 [269337600/2] via      695.0000.0c3e.7424, age 00:15:12,
>                          1u, Et0
>
> There's no sign of network 12345678. The same thing happens for a an
> aggregated floating static. A floating static for a specific network workd
> fine but not for an aggregated route. I've rebooted routers etc. I was
> wondering if someoen could simulate this and give some feedback.
>
> Thanks again
>
> bob
>
> ----- Original Message -----
> From: "rsevier" <rsevier@zealousolutions.com>
> To: "Bob Chahal" <bob.chahal@ntlworld.com>; <ccielab@groupstudy.com>
> Sent: Sunday, August 26, 2001 4:11 PM
> Subject: RE: redistributing IPX floating static
>
>
> > B-  First you have a IP route rather than an IPX route, but I think that
> is
> > a typo because I don't think the router will allow you to input that
> > statement.  Also, you mention floating static in the subject, but I
don't
> > see any evidence of a floating static route anywhere in your post.  Post
a
> > config and a sho ipx route, and I think we can figure it out.
> >
> > Raymond
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Bob Chahal
> > Sent: Sunday, August 26, 2001 1:26 AM
> > To: ccielab@groupstudy.com
> > Subject: redistributing IPX floating static
> >
> >
> > I can't seem to redistribute aggregated statics or floating statics into
> rip
> > or eigrp. For example, if a create an aggregate static route for ipx
> > networkds 800 to 803 by
> >
> > ip route 800 fffffffc 6005.0000.6666.0000
> >
> > then do
> >
> > ipx router eigrp 1
> > redistribute static
> >
> > the aggregate route is not propagated to the other routers in the EIGRP
> > routing domain. I've tried this on v11.2 and v12.07. Has anyone got a
> > solution for this? or seen this before?
> >
> > Once again appreciate any feedback on this.
> >
> > Thanks
> >
> > Bob
> > **Please read:http://www.groupstudy.com/list/posting.html
> **Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:31:58 GMT-3