From: Taimoor Husain (taimoor@xxxxxxxxx)
Date: Sat May 18 2002 - 20:12:28 GMT-3
Your configuration looks correct and contrary to popular beleif, so does
your csim start output. I would suggest if you hgave physical access to the
rack, try attaching analog phones on the fxs ports and actually making the
calls. you should be able to ring the phone.
Thanks.
Taimoor
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> cash2001
> Sent: Saturday, May 18, 2002 3:27 PM
> To: ccielab@groupstudy.com
> Subject: Voice lab from All-in-OneCisco CCIE
>
>
> I am stuck on a voice lab scenario from the Satterlee book. The traffic
> is traversing an ATM link. Please excuse any ignorance as this is my
> first post and in the book, there is no way to test the connectivity.
> Also, what would/should a successful 'csim' output look like?
>
> --------( R6 ) ------- --( R9 )------ -- ( R11 ) -----
> FXS ---- ATM3/0 ----- ATM0 --- S1--- S0/0 ---- FXS
>
> Output from csim start:
>
> r6#csim start 3333
> csim: called number = 3333, loop count = 1 ping count = 0
>
> csim: loop = 1, failed = 1
> csim: call attempted = 1, setup failed = 1, tone failed = 0
>
> Configs (R6):
>
> version 12.1
> no service single-slot-reload-enable
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname r6
> !
> logging rate-limit console 10 except errors
> !
> memory-size iomem 10
> ip subnet-zero
> !
> no ip finger
> no ip domain-lookup
> !
> ip audit notify log
> ip audit po max-events 100
> !
> call rsvp-sync
> cns event-service server
> !
> interface Loopback0
> ip address 135.25.2.1 255.255.255.255
> !
> interface BRI0/0
> no ip address
> shutdown
> !
> interface Ethernet0/0
> no ip address
> shutdown
> half-duplex
> !
> interface Serial0/0
> ip address 192.1.1.3 255.255.255.0
> encapsulation frame-relay
> no fair-queue
> frame-relay lmi-type ansi
> !
> interface TokenRing0/0
> no ip address
> shutdown
> ring-speed 16
> !
> interface FastEthernet1/0
> no ip address
> shutdown
> duplex auto
> speed auto
>
> Configs (R11):
>
> version 12.1
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname r11
> !
> memory-size iomem 10
> ip subnet-zero
> !
> ip audit notify log
> ip audit po max-events 100
> !
> voice-port 1/0/0
> !
> voice-port 1/0/1
> !
> dial-peer voice 1 pots
> destination-pattern 3333
> port 1/0/0
> !
> dial-peer voice 2 voip
> destination-pattern 2222
> session target ipv4:135.25.2.1
> !
> dial-peer voice 3 voip
> destination-pattern 2222
> session target ipv4:135.25.2.1
> !
> interface Loopback0
> ip address 135.25.3.1 255.255.255.255
> !
> interface FastEthernet0/0
> no ip address
> shutdown
> duplex auto
> speed auto
> !
> interface Serial0/0
> ip address 195.1.2.2 255.255.255.252
> no fair-queue
> !
> interface Serial0/1
> no ip address
> shutdown
> !
> router ospf 64
> log-adjacency-changes
> network 135.25.0.0 0.0.255.255 area 0
> network 195.1.0.0 0.0.255.255 area 0
> !
> ip classless
> ip http server
> !
> line con 0
> line aux 0
> line vty 0 4
> !
> no scheduler allocate
> end
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 10:59:00 GMT-3