From: Horszczaruk Krzysztof (Krzysztof.Horszczaruk@xxxxxxxxxxxxx)
Date: Tue Aug 06 2002 - 04:06:03 GMT-3
dialer in-band ?
>>>-----Original Message-----
>>>From: syv [mailto:syv@911networks.com]
>>>Sent: Sunday, August 04, 2002 1:25 AM
>>>To: ccielab@groupstudy.com
>>>Subject: Dialer with AUX back to back
>>>
>>>
>>>Hi,
>>>
>>>I have 2 routers connected back to back through the Aux port
>>>with a console cable.
>>>
>>>=====Works=====Works=====Works=====Works=====Works
>>>Aux to aux with console cable
>>>
>>>Same on both sides:
>>>
>>>interface Async1
>>> ip address 192.168.10.2 255.255.255.0
>>> encapsulation ppp
>>> async dynamic routing
>>> async mode dedicated
>>>
>>>
>>>line aux 0
>>> exec-timeout 0 0
>>> logging synchronous
>>> modem InOut
>>> transport input all
>>> flowcontrol hardware
>>>
>>>c2505#p 192.168.10.1
>>>
>>>Type escape sequence to abort.
>>>Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:
>>>!!!!!
>>>Success rate is 100 percent (5/5), round-trip min/avg/max =
>>>240/240/240 ms
>>>c2505#
>>>
>>>=====Does not work =====Does not work=====Does not
>>>work=====Does not work
>>>Missing dialer map ip 192.168.10.1 name c2505 on dialer
>>>interface. I cannot enter it, it's not a valid option!
>>>
>>>username c2502 password 0 123456
>>>
>>>interface Async1
>>> no ip address
>>> encapsulation ppp
>>> dialer in-band
>>> dialer pool-member 1
>>> async dynamic routing
>>> async mode dedicated
>>>!
>>>interface Dialer1
>>> ip address 192.168.10.2 255.255.255.0
>>> dialer pool 1
>>> dialer-group 1
>>> no cdp enable
>>>!
>>>access-list 101 remark .............for dialer-list 1
>>>access-list 101 permit icmp any any
>>>access-list 101 permit ip any any
>>>dialer-list 1 protocol ip list 101
>>>!
>>>line aux 0
>>> exec-timeout 0 0
>>> logging synchronous
>>> modem InOut
>>> transport input all
>>> flowcontrol hardware
>>>end
>>>
>>>c2505#
>>>
>>>c2505#sh deb
>>>Dial on demand:
>>> Dial on demand events debugging is on
>>>
>>>c2505#p 192.168.10.1
>>>
>>>Type escape sequence to abort.
>>>Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:
>>>
>>>Aug 3 16:16:21 PDT: Di1 DDR: Cannot place call, no dialer
>>>string set.
>>>Aug 3 16:16:23 PDT: Di1 DDR: Cannot place call, no dialer
>>>string set.
>>>Aug 3 16:16:25 PDT: Di1 DDR: Cannot place call, no dialer
>>>string set.
>>>Aug 3 16:16:27 PDT: Di1 DDR: Cannot place call, no dialer
>>>string set.
>>>Aug 3 16:16:29 PDT: Di1 DDR: Cannot place call, no dialer
>>>string set.
>>>Success rate is 0 percent (0/5)
>>>
>>>c2505(config)#int di1
>>>c2505(config-if)#dialer ?
>>> callback-secure Enable callback security
>>> called Specify called telephone number to
>>>be screened
>>> caller Specify calling telephone number to
>>>be screened
>>> enable-timeout Set length of time an interface
>>>stays down before it
>>> is available for dialing
>>> fast-idle Set idle time before disconnecting
>>>line with an
>>> unusually high level of contention
>>> hold-queue Configure output hold queue
>>> idle-timeout Specify idle timeout before
>>>disconnecting line
>>> in-band Set v.25bis dialing for interface
>>> load-threshold Specify threshold for placing
>>>additional calls
>>> max-call Specify maximum number of calls
>>> pool Specify dialer pool to be used
>>> redial Configure redial for this interface
>>> remote-name Configure a remote name
>>> rotor Set outbound rotor order
>>> snapshot Enable snapshot address for dialer profile
>>> string Specify telephone number to be
>>>passed to DCE device
>>> vpdn Enable vpdn dial
>>> wait-for-carrier-time How long the router will wait for carrier
>>> watch-disable Time to wait before bringing down
>>>watched route link
>>> watch-group Assign interface to dialer-watch-list
>>>
>>>
>>>Any suggestion?
>>>
>>>----
>>>syv@911networks.com
This archive was generated by hypermail 2.1.4 : Sat Sep 07 2002 - 19:48:17 GMT-3