From: Hongtu Wang (wht_wh@sympatico.ca)
Date: Tue Sep 17 2002 - 21:50:09 GMT-3
Hi, Becky,
Normally "show cam dy" is used on Cat4K/5K. I have a 7603 router with 2 Cat 6000 supervisor engine 2 (WS-X6K-S2U-MSFC2) and 1 48 ports 10/100 module. I put a native IOS image on it. The show info as:
7603#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL06261UET
2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2 SAL06261UJL
3 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD061700FY
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0009.1243.9d4c to 0009.1243.9d4d 3.7 6.1(3) 7.2(0.90) Ok
2 0006.d65b.7f30 to 0006.d65b.7f31 3.7 6.1(3) 7.2(0.90) Ok
3 0002.7ee3.41f4 to 0002.7ee3.4223 4.3 6.3(1) 7.2(0.90) Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- --------------- --------------- ------- -------
1 Policy Feature Card 2 WS-F6K-PFC2 SAL06261MPV 3.2 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K60 2.3 Ok
2 Policy Feature Card 2 WS-F6K-PFC2 SAL06261M2X 3.2 Other
2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K4Z 2.3 Ok
7603#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL06261UET
2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2 SAL06261UJL
3 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD061700FY
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0009.1243.9d4c to 0009.1243.9d4d 3.7 6.1(3) 7.2(0.90) Ok
2 0006.d65b.7f30 to 0006.d65b.7f31 3.7 6.1(3) 7.2(0.90) Ok
3 0002.7ee3.41f4 to 0002.7ee3.4223 4.3 6.3(1) 7.2(0.90) Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- --------------- --------------- ------- -------
1 Policy Feature Card 2 WS-F6K-PFC2 SAL06261MPV 3.2 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K60 2.3 Ok
2 Policy Feature Card 2 WS-F6K-PFC2 SAL06261M2X 3.2 Other
2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K4Z 2.3 Ok
7603#sh ver
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JO3SV-M), Version 12.1(12c)E1, EARLY DEP)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 07-Aug-02 17:42 by eaarmas
Image text-base: 0x40008980, data-base: 0x419C6000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: c6sup2_rp Software (c6sup2_rp-JO3SV-M), Version 12.1(12c)E1, EARLY DEP)
7603 uptime is 1 week, 1 day, 1 hour, 56 minutes
System returned to ROM by power-on (SP by power-on)
System image file is "slot0:c6sup22-jo3sv-mz.121-12c.E1"
cisco Catalyst 6000 (R7000) processor with 489472K/34816K bytes of memory.
Processor board ID SAL06251K60
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Virtual Ethernet/IEEE 802.3 interface(s)
48 FastEthernet/IEEE 802.3 interface(s)
4 Gigabit Ethernet/IEEE 802.3 interface(s)
381K bytes of non-volatile configuration memory.
16384K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x102
7603#
7603#
7603#sh cam ?
% Unrecognized command
7603#sh cam
As you can see, when I typed "sh cam ?", it said "% Unrecognized command". Can you or anybody tell me how to find out cam table on it?
Thanks
Hongtu Wang
----- Original Message -----
From: "Becky Qiang" <becky.qiang@wincomsystems.com>
To: "Hongtu Wang" <wht_wh@sympatico.ca>; <ccielab@groupstudy.com>
Sent: Tuesday, September 17, 2002 6:58 PM
Subject: Re: how to show cam table on 6500
> Hi Hongtu:
>
> You can do a 'show cam dy' to show the cam table. Also, you can do a 'show
> cam ?' to see other show cam options.
>
> Becky
>
>
>
> ----- Original Message -----
> From: "Hongtu Wang" <wht_wh@sympatico.ca>
> To: <ccielab@groupstudy.com>
> Sent: Monday, September 16, 2002 4:40 PM
> Subject: how to show cam table on 6500
>
>
> > We have a cat 6500 running native IOS. Can anybody tell me how to show cam
> table on it?
> >
> > Thanks
This archive was generated by hypermail 2.1.4 : Mon Oct 07 2002 - 07:43:55 GMT-3