From: Jason Sinclair (sinclairj@powertel.com.au)
Date: Tue Sep 17 2002 - 22:18:16 GMT-3
Wouldn't you just use show arp as per any IOS enabled device?
Jason Sinclair CCIE #9100
Manager, Network Control Centre
POWERTEL
55 Clarence Street,
SYDNEY NSW 2000
AUSTRALIA
office: + 61 2 8264 3820
mobile: + 61 416 105 858
email: sinclairj@powertel.com.au
-----Original Message-----
From: Hongtu Wang [mailto:wht_wh@sympatico.ca]
Sent: Wednesday, 18 September 2002 10:50
To: Becky Qiang; ccielab@groupstudy.com
Subject: Re: how to show cam table on 6500
Hi, Becky,
Normally "show cam dy" is used on Cat4K/5K. I have a 7603 router with 2 Cat
6000 supervisor engine 2 (WS-X6K-S2U-MSFC2) and 1 48 ports 10/100 module. I
put a native IOS image on it. The show info as:
7603#sh module
Mod Ports Card Type Model Serial
No.
--- ----- -------------------------------------- ------------------
-----------
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2
SAL06261UET
2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2
SAL06261UJL
3 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45
SAD061700FY
Mod MAC addresses Hw Fw Sw
Status
--- ---------------------------------- ------ ------------ ------------
-------
1 0009.1243.9d4c to 0009.1243.9d4d 3.7 6.1(3) 7.2(0.90) Ok
2 0006.d65b.7f30 to 0006.d65b.7f31 3.7 6.1(3) 7.2(0.90) Ok
3 0002.7ee3.41f4 to 0002.7ee3.4223 4.3 6.3(1) 7.2(0.90) Ok
Mod Sub-Module Model Serial Hw
Status
--- --------------------------- --------------- --------------- -------
-------
1 Policy Feature Card 2 WS-F6K-PFC2 SAL06261MPV 3.2 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K60 2.3 Ok
2 Policy Feature Card 2 WS-F6K-PFC2 SAL06261M2X 3.2
Other
2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K4Z 2.3 Ok
7603#sh module
Mod Ports Card Type Model Serial
No.
--- ----- -------------------------------------- ------------------
-----------
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2
SAL06261UET
2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2
SAL06261UJL
3 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45
SAD061700FY
Mod MAC addresses Hw Fw Sw
Status
--- ---------------------------------- ------ ------------ ------------
-------
1 0009.1243.9d4c to 0009.1243.9d4d 3.7 6.1(3) 7.2(0.90) Ok
2 0006.d65b.7f30 to 0006.d65b.7f31 3.7 6.1(3) 7.2(0.90) Ok
3 0002.7ee3.41f4 to 0002.7ee3.4223 4.3 6.3(1) 7.2(0.90) Ok
Mod Sub-Module Model Serial Hw
Status
--- --------------------------- --------------- --------------- -------
-------
1 Policy Feature Card 2 WS-F6K-PFC2 SAL06261MPV 3.2 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K60 2.3 Ok
2 Policy Feature Card 2 WS-F6K-PFC2 SAL06261M2X 3.2
Other
2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL06251K4Z 2.3 Ok
7603#sh ver
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JO3SV-M), Version 12.1(12c)E1, EARLY
DEP)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 07-Aug-02 17:42 by eaarmas
Image text-base: 0x40008980, data-base: 0x419C6000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: c6sup2_rp Software (c6sup2_rp-JO3SV-M), Version 12.1(12c)E1, EARLY
DEP)
7603 uptime is 1 week, 1 day, 1 hour, 56 minutes
System returned to ROM by power-on (SP by power-on)
System image file is "slot0:c6sup22-jo3sv-mz.121-12c.E1"
cisco Catalyst 6000 (R7000) processor with 489472K/34816K bytes of memory.
Processor board ID SAL06251K60
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Virtual Ethernet/IEEE 802.3 interface(s)
48 FastEthernet/IEEE 802.3 interface(s)
4 Gigabit Ethernet/IEEE 802.3 interface(s)
381K bytes of non-volatile configuration memory.
16384K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x102
7603#
7603#
7603#sh cam ?
% Unrecognized command
7603#sh cam
As you can see, when I typed "sh cam ?", it said "% Unrecognized command".
Can you or anybody tell me how to find out cam table on it?
Thanks
Hongtu Wang
----- Original Message -----
From: "Becky Qiang" <becky.qiang@wincomsystems.com>
To: "Hongtu Wang" <wht_wh@sympatico.ca>; <ccielab@groupstudy.com>
Sent: Tuesday, September 17, 2002 6:58 PM
Subject: Re: how to show cam table on 6500
> Hi Hongtu:
>
> You can do a 'show cam dy' to show the cam table. Also, you can do a 'show
> cam ?' to see other show cam options.
>
> Becky
>
>
>
> ----- Original Message -----
> From: "Hongtu Wang" <wht_wh@sympatico.ca>
> To: <ccielab@groupstudy.com>
> Sent: Monday, September 16, 2002 4:40 PM
> Subject: how to show cam table on 6500
>
>
> > We have a cat 6500 running native IOS. Can anybody tell me how to show
cam
> table on it?
> >
> > Thanks
**********************************************************************
PowerTel Limited, winners of
Broadband Wholesale Carrier of the year, CommsWorld Telecomms Awards 2001
Best Emerging Telco, Australian Telecom Awards 2001
**********************************************************************
This email (including all attachments) is intended solely for the named
addressee. It is confidential and may contain commercially sensitive
information. If you receive it in error, please let us know by reply email,
delete it from your system and destroy any copies.
This email is also subject to copyright. No part of it should be reproduced,
adapted or transmitted without the prior written consent of the copyright owner.
Emails may be interfered with, may contain computer viruses or other defects
and may not be successfully replicated on other systems. We give no
warranties in relation to these matters. If you have any doubts about
the authenticity of an email purportedly sent by us, please contact us
immediately.
**********************************************************************
This archive was generated by hypermail 2.1.4 : Mon Oct 07 2002 - 07:43:55 GMT-3