From: Mingzhou Nie (mnie@yahoo.com)
Date: Thu Sep 19 2002 - 15:43:16 GMT-3
You are correct, Bradford. "modem host" is calling, "modem dialin" is
called. You can, however, make both routers callin and callout by
replacing above to "modem inout".
Ming
--- "Hung, Sing-Yu" <Sing-Yu.Hung@pccw.com> wrote:
> Dear,
>
> Can any confirm that it is only host can make a connection to
> "Dialin".i.e calling can make a connection to called routed router,
> but
> called not.
>
> Bradford Hung
>
> > Pacific Century CyberWorks
> > Tel: 288 33125
>
>
> -----Original Message-----
> From: Roberts, Larry [mailto:Larry.Roberts@expanets.com]
> Sent: Thursday, September 19, 2002 10:14 AM
> To: 'Le Dinh An'; syv
> Cc: ccielab@groupstudy.com
> Subject: RE: Aux back to back problem
>
>
> Here are some working configs ( albiet with OSPF demand routing )
>
> Calling ROuter
>
> interface Async65
> no ip address
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> dialer in-band
> dialer pool-member 1
> async default routing
> async dynamic routing
> async mode dedicated
>
> interface Dialer0
> ip address 192.168.12.1 255.255.255.0
> encapsulation ppp
> ip ospf message-digest-key 1 md5 7 094F471A1A0A
> ip ospf demand-circuit
> ip ospf demand-circuit
> dialer pool 1
> dialer idle-timeout 60
> dialer string 1234
> dialer-group 1
> no peer neighbor-route
> no peer default ip address
> no cdp enable
> ppp authentication chap
> ppp chap hostname r1
> ppp chap password 7 05080F1C2243
> !
> line aux 0
> exec-timeout 0 0
> script dialer myscript
> modem Host
> transport input all
> speed 19200
> flowcontrol hardware
>
> Called ROuter
>
> interface Async65
> no ip address
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> dialer in-band
> dialer pool-member 1
> async default routing
> async dynamic routing
> async mode dedicated
> !
> interface Dialer0
> ip address 192.168.12.2 255.255.255.0
> encapsulation ppp
> no ip route-cache
> ip ospf message-digest-key 1 md5 7 104D000A0618
> ip ospf demand-circuit
> no ip mroute-cache
> dialer pool 1
> dialer-group 1
> no peer neighbor-route
> no cdp enable
> ppp authentication chap callin
> ppp chap hostname r2
> ppp chap password 7 01100F175804
> !
> line aux 0
> exec-timeout 0 0
> script dialer myscript
> modem Dialin
> transport input all
> speed 19200
> flowcontrol hardware
>
>
> Thanks
>
> Larry
>
>
> -----Original Message-----
> From: Le Dinh An [mailto:anld@ispco.com.vn]
> Sent: Wednesday, September 18, 2002 8:45 PM
> To: syv
> Cc: ccielab@groupstudy.com
> Subject: Re: Aux back to back problem
>
>
> 'modem host' under line aux 0 of the calling router.
>
> You can have the working configs some days earlier on this list.
>
> An.
>
> syv wrote:
>
> >Hi,
> >
> >I have 2 router c1751 and c2505 connected back to back
> >through the Aux port.
> >
> >No routing install but it still goes up and down like a yoyo:
> >
> >Sep 18 15:46:15 PDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface
>
> >Async1, changed state to up Sep 18 15:48:12 PDT: %DIALER-6-UNBIND:
> >Interface As1 unbound from profile Di0 Sep 18 15:48:14 PDT:
> >%LINK-5-CHANGED: Interface Async1, changed state to reset Sep 18
> >15:48:15 PDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Async1,
> >changed state to down Sep 18 15:48:19 PDT: %LINK-3-UPDOWN: Interface
>
> >Async1, changed state to up Sep 18 15:48:19 PDT: %DIALER-6-BIND:
> >Interface As1 bound to profile Di0 Sep 18 15:48:22 PDT:
> >%LINEPROTO-5-UPDOWN: Line protocol on Interface Async1, changed
> state
> >to up Sep 18 15:50:19 PDT: %DIALER-6-UNBIND: Interface As1 unbound
> from
> >profile Di0 Sep 18 15:50:21 PDT: %LINK-5-CHANGED: Interface Async1,
> >changed state to reset Sep 18 15:50:22 PDT: %LINEPROTO-5-UPDOWN:
> Line
> >protocol on Interface Async1, changed state to down Sep 18 15:50:26
> >PDT: %LINK-3-UPDOWN: Interface Async1, changed state to up Sep 18
> >15:50:26 PDT: %DIALER-6-BIND: Interface As1 bound to profile Di0 Sep
> 18
> >15:50:29 PDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> Async1,
> >changed state to up
> >
> >Any suggestion?
> >
> >I did debug on async, on ppp and on dialer and do not see anything
> that
> >would call the interface to go up.
> >
> >The cdp does not [as defined in the dialer-list].
> >
> >Here are the configs:
> >
> >The c2505
> >
> >c2505#s
> >Building configuration...
> >
> >Current configuration : 2142 bytes
> >!
> >! Last configuration change at 10:05:14 PDT Wed Sep 18 2002
> >! NVRAM config last updated at 10:05:16 PDT Wed Sep 18 2002
> >!
> >version 12.1
> >no service single-slot-reload-enable
> >service timestamps debug datetime localtime show-timezone service
> >timestamps log datetime localtime show-timezone no service
> >password-encryption !
> >hostname c2505
> >!
> >logging buffered 16384 debugging
> >enable secret 5 $1$Btx/$Kam.aSIufLXVTpi8mx7aC1
> >!
> >username c1751 password 0 123456
> >!
> >!
> >!
> >!
> >clock timezone PST -7
> >clock summer-time PDT recurring
> >ip subnet-zero
> >no ip domain-lookup
> >!
> >chat-script script-null-modem "" ""
> >!
> >!
> >!
> >hub ether 0 1
> > link-test
> > auto-polarity
> >!
> >hub ether 0 2
>
=== message truncated ===
This archive was generated by hypermail 2.1.4 : Mon Oct 07 2002 - 07:43:57 GMT-3