From: Tony Schaffran (tschaffran@cconlinelabs.com)
Date: Thu Dec 19 2002 - 11:02:27 GMT-3
Thank you. I actually got one! WoW.
Tony Schaffran
Network Analyst
CCNP, CCNA, CCDA,
NNCDS, NNCSS, CNE, MCSE
CCOnlineLabs.com
http://www.cconlinelabs.com
-----Original Message-----
From: Matthew Poole [mailto:matthew.poole@blueyonder.co.uk]
Sent: Thursday, December 19, 2002 4:13 AM
To: Matthew Poole; Georg Pauwen; tschaffran@cconlinelabs.com;
ccielab@groupstudy.com
Subject: FIX-Re: Dialer profile
Tony was right!!!
I had a second look at the bug's and found bug ID CSCds21637
Dialer idle-timeout configured under the map-class, and applied to
dialer
map
does not overwrite dialer idle-timeout on the dialer interface.
There is no workaround
Cheers everybody.
----- Original Message -----
From: "Matthew Poole" <matthew.poole@blueyonder.co.uk>
To: "Georg Pauwen" <pauwen@hotmail.com>; <tschaffran@cconlinelabs.com>;
<ccielab@groupstudy.com>
Sent: Thursday, December 19, 2002 12:07 PM
Subject: Re: Dialer profile
> Hi Georg
>
> Thanks for looking,
>
> however dialer profiles only allow dial strings, no dialer map
command.
>
> R5(config-if)#dialer ?
> callback-secure Enable callback security
> called Specify called telephone number to be
screened
> caller Specify calling telephone number to be
screened
> enable-timeout Set length of time an interface stays down
before
> it
> is available for dialing
> fast-idle Set idle time before disconnecting line with
an
> unusually high level of contention
> hold-queue Configure output hold queue
> idle-timeout Specify idle timeout before disconnecting
line
> in-band Set v.25bis dialing for interface
> load-threshold Specify threshold for placing additional
calls
> max-call Specify maximum number of calls
> pool Specify dialer pool to be used
> redial Configure redial for this interface
> remote-name Configure a remote name
> rotor Set outbound rotor order
> snapshot Enable snapshot address for dialer profile
> string Specify telephone number to be passed to DCE
device
> vpdn Enable vpdn dial
> wait-for-carrier-time How long the router will wait for carrier
> watch-disable Time to wait before bringing down watched
route
> link
> watch-group Assign interface to dialer-watch-list
>
> Any other ideas??
>
> Mat.
> ----- Original Message -----
> From: "Georg Pauwen" <pauwen@hotmail.com>
> To: <tschaffran@cconlinelabs.com>; <matthew.poole@blueyonder.co.uk>;
> <ccielab@groupstudy.com>
> Sent: Wednesday, December 18, 2002 9:09 PM
> Subject: Re: Dialer profile
>
>
> > Hi Matthew,
> >
> > I think the map-class commnd only works in combination with dialer
map
> > statements in your dialer configuration and not with dialer
> > remote-name/dialer string commands. Can you give it a try ?
> >
> > Regards,
> >
> > Georg
> >
> >
> >
> >
> >
> >
> > >From: "Tony Schaffran" <tschaffran@cconlinelabs.com>
> > >Reply-To: "Tony Schaffran" <tschaffran@cconlinelabs.com>
> > >To: "Matthew Poole" <matthew.poole@blueyonder.co.uk>,
> > ><ccielab@groupstudy.com>
> > >Subject: Re: Dialer profile
> > >Date: Tue, 17 Dec 2002 09:44:29 -0800
> > >
> > >I am looking at the same thing. It appears that the idle-timeout
in
the
> > >map-class statement does not apply within a dialer interface.
> > >
> > >It does, however work if it is applied to a physical interface.
> > >
> > >A hidden IOS "feature" maybe?
> > >
> > >
> > >
> > >Tony Schaffran
> > >Network Analyst
> > >CCNP, CCNA, CCDA,
> > >NNCSS, NNCDS, CNE, MCSE
> > >
> > >CCOnlineLabs.com
> > >http://www.cconlinelabs.com
> > >
> > >
> > >
> > >----- Original Message -----
> > >From: "Matthew Poole" <matthew.poole@blueyonder.co.uk>
> > >To: <ccielab@groupstudy.com>
> > >Sent: Tuesday, December 17, 2002 4:53 AM
> > >Subject: Dialer profile
> > >
> > >
> > > > I'm trying to configure a map-class dialer for my dialer profile
so
> that
> > >the
> > > > line clears down after 20 seconds:
> > > >
> > > > interface BRI0/0
> > > > no ip address
> > > > encapsulation ppp
> > > > dialer pool-member 1
> > > > isdn switch-type basic-net3
> > > > ppp authentication chap
> > > > !
> > > > !
> > > > interface Dialer1
> > > > ip address 192.168.1.1 255.255.255.0
> > > > encapsulation ppp
> > > > dialer pool 1
> > > > dialer remote-name R4
> > > > dialer string 325600 class profile
> > > > dialer-group 1
> > > > ppp authentication chap
> > > > !
> > > > !
> > > > map-class dialer profile
> > > > dialer idle-timeout 20
> > > > dialer fast-idle 15
> > > > dialer-list 1 protocol ip permit
> > > >
> > > > However when I do a ping and show isdn active, the ping is
successful
> > >but
> > >the
> > > > idle timout is still 120 Seconds? Output is below with debug
dialer.
> > > >
> > > > R5#ping 192.168.1.2
> > > >
> > > > Type escape sequence to abort.
> > > > Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2
seconds:
> > > >
> > > > 00:47:09: BR0/0 DDR: rotor dialout [priority]
> > > > 00:47:09: BR0/0 DDR: Dialing cause ip (s=192.168.1.1,
d=192.168.1.2)
> > > > 00:47:09: BR0/0 DDR: Attempting to dial 325600
> > > > 00:47:47244640255: %LINK-3-UPDOWN: Interface BRI0/0:2, changed
state
> to
> > >up
> > > > 00:47:45123225436: BR0/0:2: interface must be fifo queue, force
fifo
> > > > 00:47:45123225252: %DIALER-6-BIND: Interface BR0/0:2 bound to
profile
> > > > Di1.!!!!
> > > > Success rate is 80 percent (4/5), round-trip min/avg/max =
28/31/32
ms
> > > > R5#
> > > > 00:47:10: BR0/0:2 DDR: dialer protocol up
> > > > R5#
> > > > 00:47:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface
BRI0/0:2,
> > >changed
> > > > stat
> > > > e to up
> > > > R5#sh isdn active
> > > >
> >
>
>-----------------------------------------------------------------------
--- > > >--- > > > > --- > > > > ISDN ACTIVE CALLS > > > > > > > >----------------------------------------------------------------------- --- > > >--- > > > > --- > > > > Call Calling Called Remote Seconds Seconds Seconds > > >Charges > > > > Type Number Number Name Used Left Idle > > > > Units/Currency > > > > > > > >----------------------------------------------------------------------- --- > > >--- > > > > --- > > > > Out 325600 R4 6 114 5 > 0 > > > > > > > >----------------------------------------------------------------------- --- > > >--- > > > > --- > > > > > > > > I've tried it by also placing dialer idle-timeout directly in the > dialer > > >but > > > > this had the same affect (i.e none!) > > > > > > > > Any ideas why it doesn't indicate 20 Seconds? Thanks. > > > > . > > >. > > _________________________________________________________________ > > Add photos to your messages with MSN 8. Get 2 months FREE*. > > http://join.msn.com/?page=features/featuredemail > > . .
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:49 GMT-3