From: Hunt Lee (huntl@webcentral.com.au)
Date: Thu Dec 26 2002 - 20:46:01 GMT-3
Hello Eugene,
Are you sure??? I thought that the 'dlsw icanreach mac-exclusive" command
should always be together with the "dlsw icanreach mac-address" command,
which is on RTB???
Best Regards,
Hunt Lee
-----Original Message-----
From: eward15@juno.com [mailto:eward15@juno.com]
Sent: Friday, 27 December 2002 12:36 AM
To: ccielab@groupstudy.com
Subject: Re:DLSW+ - please help!!!
I could be wrong, but according to your diagram, I think that you have the
icanreach mac-exclusive/mac-address commands on the wrong router. Put them
of RTC.
Eugene Ward
My question - is there any trick to the commands:-
dlsw icanreach mac-exclusive
&
dlsw icanreach mac-address ?
I have the following lab setup:-
RTA
/ \
WebCentral11---RTB RTC --- Hardcat-laptop
Both workstations are on Ethernet.
And the three routers are in a Frame-relay network.
I must have done something fundermentally wrong. Since if I remove the 2
icanreach
commands, everything is ok (i.e. I can see Network neighborhood, I can see
the
DLSW
circuit up etc). But as soon as I put back the commands, I can't see
anything.
My laptop (WebCentral11)'s MAC address is 0050.04b9.4584.
C:\>ipconfig /all
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : FE575C-3COM 10/100 LAN CardBus-Fast
Ethernet
Physical Address. . . . . . . . . : 00-50-04-B9-45-84
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Autoconfiguration IP Address. . . : 169.254.205.7
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :
C:\>
And I have confirmed it with:-
RTB#sh bridge
Total of 300 station blocks, 298 free
Codes: P - permanent, S - self
Bridge Group 1:
Address Action Interface Age RX count TX count
0050.ba76.ea5f forward DLSw Port0 0 1 1
0050.04b9.4584 forward Ethernet0 0 1 0
RTB#
RTC#sh bridge
Total of 300 station blocks, 298 free
Codes: P - permanent, S - self
Bridge Group 1:
Address Action Interface Age RX count TX count
0050.ba76.ea5f forward Ethernet0 0 9 1
0050.04b9.4584 forward DLSw Port0 0 1 3
RTC#
And here's the config:-
For RTB-
dlsw local-peer peer-id 1.1.1.1 promiscuous
dlsw icanreach mac-exclusive
dlsw icanreach mac-address 0050.04b9.4584 mask ffff.ffff.ffff
dlsw bridge-group 1
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface Ethernet0
no ip address
bridge-group 1
bridge 1 protocol ieee
As for RTC-
dlsw local-peer peer-id 2.2.2.2
dlsw remote-peer 0 tcp 1.1.1.1
dlsw bridge-group 1
interface Loopback1
ip address 2.2.2.2 255.255.255.255
interface Ethernet0
no ip address
bridge-group 1
bridge 1 protocol ieee
It would be greatly appreciated if anyone can shed some light on this.
This archive was generated by hypermail 2.1.4 : Fri Jan 17 2003 - 17:21:53 GMT-3