From: kasturi cisco (kasturi_cisco@hotmail.com)
Date: Sat Jun 07 2003 - 10:49:20 GMT-3
I was looking at ur configs/my notes more closely and wanted to know why
u are using "Fr-relay map dlsw" under ur interfaces. When u use DLSWlite
we need mapping only "fr map llc2" and "fr map ip". Fr relay map dlsw
mapping is needed for Direct encapsulation.
Good Luck,
Kasturi.
>From: beda jain >Reply-To: beda jain >To: chenry@reuna.cl >CC:
ccielab@groupstudy.com >Subject: Re: dlsw lite >Date: Fri, 06 Jun 2003
11:10:43 -0400 > >Hi, > >router 5 > >dlsw local-peer peer-id 150.50.5.5
>dlsw remote-peer 0 frame-relay interface Serial2/0 501 >! > > >
>interface Serial2/0 > ip address 150.50.100.5 255.255.255.224 >
encapsulation frame-relay > no ip route-cache > ip ospf
message-digest-key 1 md5 cisco > no ip mroute-cache > frame-relay map
dlsw 501 > frame-relay map llc2 501 broadcast > frame-relay map clns 501
broadcast > frame-relay map ip 150.50.100.2 501 broadcast IETF
>payload-compression FRF9 stac > frame-relay map ip 150.50.100.5 501 >
frame-relay map ip 150.50.100.6 501 broadcast >! >interface Serial3/0 >
>router 2 >------------- >dlsw local-peer peer-id 150.50.2.2 >dlsw
remote-peer 0 frame-relay interface Serial2/0.24 104 >dlsw remote-peer 0
frame-relay interface Serial2/0.256 105 > > >interface Serial2/0.256
multipoint > ip address 150.50.100.2 255.255.255.224 > no ip
split-horizon > ip ospf message-digest-key 1 md5 cisco > ip ospf priority
200 > no ip mroute-cache > frame-relay map dlsw 105 > frame-relay map
llc2 105 broadcast > frame-relay map llc2 106 broadcast > frame-relay map
clns 105 broadcast > frame-relay map ip 150.50.100.2 105 > frame-relay
map ip 150.50.100.5 105 broadcast IETF >payload-compression FRF9 stac >
>5#sh dlsw pe >r5#sh dlsw peers >Peers: state pkts_rx pkts_tx type drops
ckts >TCP uptime > LLC2 Se2/0 501 DISCONN 0 0 conf 0 0 > - - >Total
number of connected peers: 0 >Total number of connections: 0 > >i can
ping between two loopback. but i did not see any peer beetween >this two.
>When i try the same thing with p2p network it works fine. Any help?? > >
> > >At 10:38 AM 6/6/2003 -0400, you wrote: >>dlsw remote-peer 0
frame-relay interface serial 0 30 >>! >>interface serial 0 >>
encapsulation frame-relay >>! >>interface serial 0.1 multi >> frame-relay
map dlsw 30 >>! >> >>I suggest you looks the examples on Karl Solie. >>
>> >>beda jain ha escrito: >> > >> > Does dlsw lite support in frame
relay multi point interface. >> > >> > Thanks, >> > Beda >> >>--
>>Cristian E. Henry >>REUNA >> >>E-mail: chenry@reuna.cl >>Fono:
56-2-3370336
------------------------------------------------------------------------
Go down memory lane. Revisit the cool times. Reconnect with old friends!
This archive was generated by hypermail 2.1.4 : Fri Jul 04 2003 - 11:10:54 GMT-3