From: Barney Gaumer (bagaumer@yahoo.com)
Date: Thu Sep 25 2003 - 15:19:30 GMT-3
Thanks Ian!
I'll give it a try.
Thanks again!!
Banrey
--- "istong@stong.org" <istong@stong.org> wrote:
> Hi Barney,
>
> Here are some commands you can use to configure
> PVC's and SVC's on your
> LS100.
> This sets up pvc's and svc's between ports 0 and 2.
> You can expand it to
> include port 4 if needed.
>
> So for port 0 and vpi/vci 0/33 to port 2 vpi/vci
> 0/34 using oc3 interface:
>
> pvc est 1 2 0 0 33 512 0 155 2 0 34 512 0 155
>
>
> Then you can use the following to setup the
> interfaces:
>
> set int 0 0 0 4 8 1 1 1
> set int 2 0 0 4 8 1 1 1
>
>
> Lastly if you want SVC's you would use the following
> commands (you can use
> your own nsap address and mac address as desired):
>
> route add 4701000000000000000000000000000c38a91100
> nsap 2
> route add 4701000000000000000000000000000c38a91401
> nsap 2
> route add 470100000000000000000000000060836cf84000
> nsap 0
> route add 470100000000000000000000000060836cf84101
> nsap 0
>
>
> Thanks,
>
> Ian
>
>
> Original Message:
> -----------------
> From: Barney Gaumer bagaumer@yahoo.com
> Date: Wed, 24 Sep 2003 20:22:57 -0700 (PDT)
> To: istong@stong.org, ccielab@groupstudy.com
> Subject: RE: General ATM Questions
>
>
> Would be much appreciated.
>
> Here's some info from the LS100 if it helps?
>
> atm#sh int
> Line Inf_type Physical Layer Forum/ITU Vd VPI Vd VCI
> LBO PLCP Scramble
> 0 pri_UNI OC-3C(MMF) ATM Forum 4 8
> Lo Direct ON
> 2 pri_UNI OC-3C(MMF) ATM Forum 4 8
> Lo Direct ON
> 4 pri_UNI OC-3C(MMF) ATM Forum 4 8
> Lo Direct ON
>
>
> Local Information:
> Host Name :atm
> IP Address :192.168.250.4
> Net Mask :255.255.255.0
> Ether IP Address:0.0.0.0
> Ether Net Mask :0.0.0.0
> Router(Ether) :0.0.0.0
> sysContact :
> sysLocation :
> ATM Address :01000000000000000000000000
>
> NMS Information:
> NMS Number 0 1
>
> 2 3
>
-----------+----------------+----------------+----------------+-------------
> ---
> IP Address : 0.0.0.0 0.0.0.0
> 0.0.0.0 0.0.0.0
> NetMask : 0.0.0.0 0.0.0.0
> 0.0.0.0 0.0.0.0
> Gateway : 0.0.0.0 0.0.0.0
> 0.0.0.0 0.0.0.0
> Line Number: 0 0
>
> 0 0
> VPI/VCI : 0/ 0 0/ 0
> 0/ 0 0/ 0
> Community
>
>
> Thanks,
> Barney
>
> --- Ian Stong <istong@stong.org> wrote:
> > I can generate a basic config for you. It's hard
> to
> > send you one because your setup is unique and also
> the LS100 does
> > not have a command like show running or write
> terminal to output the
> > configuration. You have to run commands for each
> piece of the setup to
> > see how it is configured.
> >
> > Ian
> >
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com
> > [mailto:nobody@groupstudy.com] On Behalf Of
> > Barney Gaumer
> > Sent: Wednesday, September 24, 2003 10:47 PM
> > To: ccielab@groupstudy.com
> > Subject: General ATM Questions
> >
> > Can anyone tell me where I might find sample
> configs
> > for a LS100 for Basic PVC/SVC setup.
> >
> > The ATM hosts are 7505's w/1 AIP controller each.
> >
> > I'm an ATM newb (never have had it in my
> > environment)
> > so I need as much help as I can get.
> >
> > Thanks,
> > Barney
> >
> >
> > __________________________________
> > Do you Yahoo!?
> > Yahoo! SiteBuilder - Free, easy-to-use web site
> > design software
> > http://sitebuilder.yahoo.com
> >
> > ***Get your CCIE and a FREE vacation:
> > Shop.GroupStudy.com***
> >
>
This archive was generated by hypermail 2.1.4 : Wed Oct 01 2003 - 07:24:37 GMT-3