From: Peng Zheng (zpnist@yahoo.com)
Date: Thu Dec 11 2003 - 22:43:49 GMT-3
After I remove ip ospf net point-to-point from
loopback 0 (150.1.5.5/24)
Then, change dialer watch to
dialer watch 1 ip 150.1.5.5 255.255.255.255
Then It works. Don't know if that's the problem.
--- Bill Lijewski <bill@eccie.com> wrote:
> Was the Serial0 interface UP when you applied the
> dialer watch-group to
> the BRI interface? I've seen this problem before,
> and the two
> suggestions that I have for you are:
>
> 1) Make sure the Serial 0 interface is up, take off
> the dialer
> watch-group from the BRI interface, shut and no shut
> the BRI, then add
> the dialer watch-group back on.
>
> 2) If step 1 didn't work, try reloading the router,
> making sure all of
> the interfaces are open before doing so.
>
> Let me know if that works.
>
>
> - Bill Lijewski
> CCIE#8642
> Network Learning Inc
> 5 Day R&S CCIE Bootcamp Instructor
> bill@eccie.com
>
> -----Original Message-----
> From: nobody@groupstudy.com
> [mailto:nobody@groupstudy.com] On Behalf Of
> Peng Zheng
> Sent: Wednesday, December 10, 2003 7:31 PM
> To: ccielab@groupstudy.com
> Subject: dialer-watch doesn't work [bcc][faked-from]
> Importance: Low
>
> I configured dialer watch between R4 and R5:
>
> R4 watch R5's loopback.
>
> After I shutdown the primary link, I got:
>
> 04:20:02: %LINK-3-UPDOWN: Interface Serial0, changed
> state to down
> 04:20:02: %OSPF-5-ADJCHG: Process 1, Nbr 150.1.5.5
> on
> Serial0 from FULL to DOWN,
> Neighbor Down: Interface down or detached
> 04:20:02: DDR: Dialer Watch: watch-group = 1
> 04:20:02: DDR: network 150.1.5.0/255.255.255.0
> DOWN,
> 04:20:02: DDR: primary DOWN
> 04:20:02: DDR: Dialer Watch: Dial Reason: Primary of
> group 1 DOWN
> 04:20:02: DDR: Dialer Watch: watch-group = 1,
> 04:20:03: %LINEPROTO-5-UPDOWN: Line protocol on
> Interface Serial0, changed state
> to down
>
> But R4 didn't dial R5.
>
>
> Config on R4:
>
> interface BRI0
> ip address 136.1.45.4 255.255.255.248
> encapsulation ppp
> no ip mroute-cache
> dialer idle-timeout 5
> dialer watch-disable 30
> dialer map ip 150.1.5.0 name Rack01R5 broadcast
> 4082222222
> dialer map ip 136.1.45.5 name Rack01R5 broadcast
> 4082222222
> dialer watch-group 1
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 40811111111 4081111111
> isdn spid2 40811111112 4081111111
> compress stac
> ppp chap password 7 062526126F61
>
>
> dialer watch-list 1 ip 150.1.5.0 255.255.255.0
> dialer watch-list 1 delay route-check initial 120
>
> Config on R5:
>
>
> interface BRI0
> ip address 136.1.45.5 255.255.255.0
> encapsulation ppp
> no ip mroute-cache
> dialer idle-timeout 0
> dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 40822222221 4082222222
> isdn spid2 40822222222 4082222222
> cdapi buffers regular 0
> cdapi buffers raw 0
> cdapi buffers large 0
> compress stac
> ppp authentication chap
>
>
>
>
>
>
>
> __________________________________
> Do you Yahoo!?
> New Yahoo! Photos - easier uploading and sharing.
> http://photos.yahoo.com/
>
>
This archive was generated by hypermail 2.1.4 : Sat Jan 03 2004 - 08:25:39 GMT-3