From: Yasser Abdullah (yasser@alharbitelecom.com)
Date: Sun May 23 2004 - 18:23:57 GMT-3
Sorry, its 'rotary 67', not 3067. Its getting late here :)
-----Original Message-----
From: "Yasser Abdullah" <yasser@alharbitelecom.com>
To: "Sergio Jimenez Arguedas" <sejimenez@its.co.cr>,
ccielab@groupstudy.com
Date: Mon, 24 May 2004 00:16:00 +0300
Subject: Re: Fw: Telnet to port 3000 !?!?!?
> You need the rotary command + the port number. So if you type in:
> rotary
> 3067, you'll just be able to telnet to port 3067 (in addition to port
> 23).
>
> I don't think you can telnet to port 3000 since the rotary command
> accept
> values from 1 to 99. So it 3001 to 3099.
>
> Brgds,
>
> Yasser
>
> -----Original Message-----
> From: "Sergio Jimenez Arguedas" <sejimenez@its.co.cr>
> To: <ccielab@groupstudy.com>
> Date: Sun, 23 May 2004 14:01:00 -0600
> Subject: Fw: Telnet to port 3000 !?!?!?
>
> > Hi Richard
> >
> >
> > Do you have "rotary x" in the line vty x?
> >
> >
> > Rgds,
> >
> >
> > Sergio
> >
> >
> >
> > ----- Original Message -----
> > From: "Richard Dumoulin" <richard.dumoulin@vanco.es>
> > To: <ccielab@groupstudy.com>
> > Sent: Sunday, May 23, 2004 12:48 PM
> > Subject: Telnet to port 3000 !?!?!?
> >
> >
> > > Hi group, I cannot figure out why thew following is not working:
> > telnet
> > > 150.1.1.1 3067
> > >
> > >
> > > Rack1R1#sh line
> > > Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
> > Overruns
> > > Int
> > > * 0 CTY - - - - - 0 0
> > 0/0
> > > -
> > > 65 AUX 9600/9600 - - - - - 0 0
> > 0/0
> > > -
> > > 66 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 67 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 68 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 69 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 70 VTY - - - - - 0 0
> > 0/0
> > > -
> > >
> > > Line(s) not in async mode -or- with no hardware support:
> > > 1-64
> > >
> > > Rack1R1#telnet 150.1.1.1 3067
> > > Trying 150.1.1.1, 3067 ...
> > > % Connection refused by remote host
> > >
> > > Rack1R1#
> > > Rack1R1#
> > > Rack1R1#sh line
> > > Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
> > Overruns
> > > Int
> > > * 0 CTY - - - - - 0 0
> > 0/0
> > > -
> > > 65 AUX 9600/9600 - - - - - 0 0
> > 0/0
> > > -
> > > 66 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 67 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 68 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 69 VTY - - - - - 0 0
> > 0/0
> > > -
> > > 70 VTY - - - - - 0 0
> > 0/0
> > > -
> > >
> > > Line(s) not in async mode -or- with no hardware support:
> > > 1-64
> > >
> > > Rack1R1# sh run int lo 0
> > > Building configuration...
> > >
> > > Current configuration : 63 bytes
> > > !
> > > interface Loopback0
> > > ip address 150.1.1.1 255.255.255.0
> > > end
> > >
> > > Rack1R1#telnet 150.1.1.1 3066
> > > Trying 150.1.1.1, 3066 ...
> > > % Connection refused by remote host
> > >
> > > Rack1R1#telnet 150.1.1.1 3000
> > > Trying 150.1.1.1, 3000 ...
> > > % Connection refused by remote host
> > >
> > >
> >
> _______________________________________________________________________
> > > Please help support GroupStudy by purchasing your study materials
> > from:
> > > http://shop.groupstudy.com
> > >
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> _______________________________________________________________________
> > Please help support GroupStudy by purchasing your study materials
> from:
> > http://shop.groupstudy.com
> >
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Jun 02 2004 - 11:12:15 GMT-3