From: nhqky888@ybb.ne.jp
Date: Tue Feb 15 2005 - 09:18:57 GMT-3
Hi all,
Im trying IPv6, however my routers do not work with following version,
- 12.2(15)T14 on C2600.
- 12.3(3) on C2500
1) int has no ipv6 ospf comnd.
R3(config)#ipv uni
R3(config)#int lo 300
R3(config-if)#ipv add FEC0::33/126
R3(config-if)#ipv ?
IPv6 interface subcommands:
address Configure IPv6 address on interface
cef Cisco Express Forwarding for IPv6
enable Enable IPv6 on interface
mtu Set IPv6 Maximum Transmission Unit
nd IPv6 interface Neighbor Discovery subcommands
redirects Enable sending of ICMP Redirect messages
rip Configure RIP routing protocol
traffic-filter Access control list for packets
unnumbered Preferred interface for source address selection
verify Enable per packet validation
R3(config-if)#
2) no entering into router process under ipv6 router ospf.
R3(config)#ipv router osp ?
<1-65535> Process ID
R3(config)#ipv router osp 100 ?
<cr>
R3(config)#ipv router osp 100
R3(config)#
3) no isis protocol.
R3(config)#router isis
Protocol not in this image
R3(config)#
4) 12.2(3) and 12.2(4)T on C2500
For IPv6, what defferences they have?
Pls give me any comment.
R3#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK9O3S3-M), Version 12.2(15)T14, RELEASE SOFTWARE
(fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 28-Aug-04 06:47 by cmong
Image text-base: 0x80008098, data-base: 0x81942B30
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-IK9O3S3-M), Version 12.2(15)T14, RELEASE SOFTWARE (fc
4)
R3 uptime is 23 minutes
System returned to ROM by power-on
System restarted at 00:02:12 UTC Mon Mar 1 1993
System image file is "flash:c2600-ik9o3s3-mz.122-15.T14.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco 2611 (MPC860) processor (revision 0x203) with 61440K/4096K bytes of memory
.
Processor board ID JAD0440088A (4262757996)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
R3#
KY
Thanks,
This archive was generated by hypermail 2.1.4 : Thu Mar 03 2005 - 08:51:20 GMT-3