From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Thu Jun 23 2005 - 13:34:12 GMT-3
Sheikh,
Issue the "maximum-paths 2" command under the EIGRP process of
the switch and then "clear ip eigrp neighbor".
HTH,
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
> Sheikh Rahman
> Sent: Wednesday, June 22, 2005 6:38 PM
> To: Brian McGahan
> Cc: ccielab@groupstudy.com
> Subject: RE: eigrp equal cost load balance
>
> Hi Brian,
>
> Please find below requested info
>
> Thanks for your help
>
> Sw config
>
> Native_6k>sh ip eigrp ne
> IP-EIGRP neighbors for process 8
> H Address Interface Hold Uptime SRTT RTO
Q
> Seq
> (sec) (ms)
Cnt
> Num
> 2 10.10.10.1 Vl2 14 00:07:27 52 312
> 0 127
> 1 10.10.10.2 Vl2 14 04:25:57 4 200
> 0 122
>
>
> Native_6k>sh ip eigrp topology
> IP-EIGRP Topology Table for AS(8)/ID(10.10.10.7)
>
> Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
> r - reply Status, s - sia Status
>
> P 20.20.1.1/32, 1 successors, FD is 2170112, tag is 31
> via 10.10.10.2 (2170112/2169856), Vlan2
>
> P 20.20.20.0/29, 1 successors, FD is 2170112
> via 10.10.10.1 (2170112/2169856), Vlan2
> via 10.10.10.2 (2170112/2169856), Vlan2
>
> Native_6k>sh ip route
>
> D 20.20.20.0/29 [90/2170112] via 10.10.10.2, 00:13:10, Vlan2
> D EX 20.20.1.1/32 [170/2170112] via 10.10.10.2, 00:12:51, Vlan2
>
> Native_6k>sh ip eigrp topology 20.20.1.1 255.255.255.255
> IP-EIGRP topology entry for 20.20.1.1/32
> State is Passive, Query origin flag is 1, 1 Successor(s), FD is
> 2170112
> Routing Descriptor Blocks:
> 10.10.10.1 (Vlan2), from 10.10.10.1, Send flag is 0x0
> Composite metric is (2170112/2169856), Route is External
> Vector metric:
> Minimum bandwidth is 1544 Kbit
> Total delay is 20010 microseconds
> Reliability is 255/255
> Load is 1/255
> Minimum MTU is 1500
> Hop count is 1
> External data:
> Originating router is 10.10.10.2
> AS number of route is 8
> External protocol is OSPF, external metric is 65
> Administrator tag is 31 (0x0000001F)
> Native_6k>
>
> Native_6k>sh ip eigrp topology 20.20.20.0 255.255.255.248
> IP-EIGRP topology entry for 20.20.20.0/29
> State is Passive, Query origin flag is 1, 1 Successor(s), FD is
> 2170112
> Routing Descriptor Blocks:
> 10.10.10.2 (Vlan2), from 10.10.10.2, Send flag is 0x0
> Composite metric is (2170112/2169856), Route is Internal
> Vector metric:
> Minimum bandwidth is 1544 Kbit
> Total delay is 20010 microseconds
> Reliability is 255/255
> Load is 1/255
> Minimum MTU is 1500
> Hop count is 1
> 10.10.10.1 (Vlan2), from 10.10.10.1, Send flag is 0x0
> Composite metric is (2170112/2169856), Route is External
> Vector metric:
> Minimum bandwidth is 1544 Kbit
> Total delay is 20010 microseconds
> Reliability is 255/255
> Load is 1/255
> Minimum MTU is 1500
> Hop count is 1
> External data:
> Originating router is 10.10.10.1
> AS number of route is 8
> External protocol is OSPF, external metric is 0
> Administrator tag is 31 (0x0000001F)
> Native_6k>
>
>
>
> -----Original Message-----
> From: Brian McGahan [mailto:bmcgahan@internetworkexpert.com]
> Sent: 23 June 2005 00:12
> To: Sheikh Rahman; ccielab@groupstudy.com
> Subject: RE: eigrp equal cost load balance
>
> Sheikh,
>
> Post the output of 'show ip eigrp neighbor', 'show ip eigrp
> topology', 'show ip eigrp topology a.b.c.d w.x.y.z' where a.b.c.d is
the
> prefix and w.x.y.z is the mask, and 'show ip route'.
>
>
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Sheikh Rahman
> > Sent: Wednesday, June 22, 2005 2:43 PM
> > To: ccielab@groupstudy.com
> > Subject: eigrp equal cost load balance
> >
> > Hi Group,
> >
> > I am having issue with the equal path load balance through eigrp
> > follwoing is my diagram
> >
> > Sw ---- R1
> > ---- R2
> >
> > I have 2 router connectes to a switch vlan10. I have assign an ip
add
> to
> > vlan 10 (1.1.1.10) R1 address .1 and r2 address .2 there is a link
> > between r1 and r2 netw for that link is 20.20.20.0 What I am tring
to
> > achive is sw should load balance 20.20.20.0
> network.
> > But in the sh ip eigrp topology I just see this network learned from
> R2
> > if I turn off r2 int then it learns from R1 but it's not load
> balancing.
> > Is there any issue with eigrp if it learns route from multiple
> neighbor
> > through one interface?
> >
> > Thanks is advance
> >
> > sheikh
> >
> >
> > Sheikh Rahman
> > Support Desk Engineer
> > Dimension Data
> > Dimension Data House
> > Building 2 , Waterfront Business Park
> > Fleet Road, Fleet
> > Hampshire GU51 3QT
> > +44 (0)12 5277 9330 Office
> > +44 (0)12 5277 9010 Fax
> > Dimension Data Home Page <http://www.didata.com>
> >
> >
> > _____
> >
> >
> > Dimension Data is a leading global technology company.
> >
> >
> >
**********************************************************************
> > This email and any files transmitted with it are confidential and
> intended
> > solely for the use of the individual or entity to whom they are
> addressed.
> > If
> > you have received this email in error please notify the system
> manager.
> >
> > Although Dimension Data has taken reasonable precautions to ensure
no
> > viruses are present in this email, the company cannot accept
> > responsibility
> for
> > any
> > loss or damage arising from the use of this email or attachments.
> >
> > www.uk.didata.com
> >
**********************************************************************
> >
> >
>
This archive was generated by hypermail 2.1.4 : Wed Jul 06 2005 - 14:43:42 GMT-3