From: Andy Tang (andytang88@gmail.com)
Date: Mon Jul 04 2005 - 17:39:03 GMT-3
Hi Brian,
Please ignore my question. I have changed two 2620s' FE_SPEED_MODE to 0=10
Mbps half-duplex mode in ROMMON. They are working fine.
Thanks/Andy
On 6/29/05, Andy Tang <andytang88@gmail.com> wrote:
>
> Hi Brian,
> I tried to install on two 2620 routers and got the same error message but
> I installed on two 2610 routers without any problem. I am appreciated if you
> can advise the solution.
>
> =======================
>
> rommon 5 > tftpdnld -r
>
> IP_ADDRESS: 10.10.10.1 <http://10.10.10.1/>
> IP_SUBNET_MASK: 255.255.255.0 <http://255.255.255.0/>
> DEFAULT_GATEWAY: 10.10.10.10 <http://10.10.10.10/>
> TFTP_SERVER: 10.10.10.10 <http://10.10.10.10/>
> TFTP_FILE: c2600-js-mz.122-15.T16.bin
> ....
> ARP: address resolution for 10.10.10.10 <http://10.10.10.10/> timed out.
> ARP failed with failure code 1. TFTP transfer aborted.
>
> TFTP: Operation terminated prematurely.
> rommon 6 >
>
> -------------
>
> Rack1R1#s ver
> Cisco Internetwork Operating System Software
> IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE
> SOFTWARE (fc4)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2004 by cisco Systems, Inc.
> Compiled Sat 28-Aug-04 06:47 by cmong
> Image text-base: 0x80008098, data-base: 0x819608A4
>
> ROM: System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)
> ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE
> (fc4)
>
> Rack1R1 uptime is 1 minute
> System returned to ROM by reload
> System image file is "flash:c2600-j1s3-mz.122-15.T14.bin"
>
> cisco 2620 (MPC860) processor (revision 0x00) with 61440K/4096K bytes of
> memory.
> Processor board ID JAD0652010H (336793937)
> M860 processor: part number 0, mask 49
> Bridging software.
> X.25 software, Version 3.0.0.
> TN3270 Emulation software.
> 1 FastEthernet/IEEE 802.3 interface(s)
> 2 Serial(sync/async) network interface(s)
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
> Rack1R1#
>
> ======================
>
> rommon 2 > tftpdnld -r
>
> IP_ADDRESS: 10.10.10.6 <http://10.10.10.6/>
> IP_SUBNET_MASK: 255.255.255.0 <http://255.255.255.0/>
> DEFAULT_GATEWAY: 10.10.10.10 <http://10.10.10.10/>
> TFTP_SERVER: 10.10.10.10 <http://10.10.10.10/>
> TFTP_FILE: c2600-js-mz.22-15.T16.bin
> ....
> ARP: address resolution for 10.10.10.10 <http://10.10.10.10/> timed out.
> ARP failed with failure code 1. TFTP transfer aborted.
>
> TFTP: Operation terminated prematurely.
> rommon 3 >
>
> -------------
>
> Rack1R6#s ver
> Cisco Internetwork Operating System Software
> IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE
> SOFTWARE (fc4)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2004 by cisco Systems, Inc.
> Compiled Sat 28-Aug-04 06:47 by cmong
> Image text-base: 0x80008098, data-base: 0x819608A4
>
> ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
> ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE
> (fc4)
>
> Rack1R6 uptime is 2 minutes
> System returned to ROM by reload
> System image file is "flash:c2600-j1s3-mz.122-15.T14.bin"
>
> cisco 2620 (MPC860) processor (revision 0x600) with 61440K/4096K bytes of
> memory.
> Processor board ID JAD060707XL (497589208)
> M860 processor: part number 0, mask 49
> Bridging software.
> X.25 software, Version 3.0.0.
> TN3270 Emulation software.
> 1 FastEthernet/IEEE 802.3 interface(s)
> 1 Serial network interface(s)
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
> Rack1R6#
>
> ========
> Thanks & regards,
> Andy
>
> On 6/28/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
> >
> > Andy,
> >
> > I believe it depends on the bootrom version. Try it out and see
> > what happens. If it doesn't work post the error messages and your "show
> > version" output.
> >
> > HTH,
> >
> > Brian McGahan, CCIE #8593
> > bmcgahan@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com <http://www.internetworkexpert.com/>
> > Toll Free: 877-224-8987 x 705
> > Outside US: 775-826-4344 x 705
> > 24/7 Support: http://forum.internetworkexpert.com
> > Live Chat: http://www.internetworkexpert.com/chat/
> >
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto: nobody@groupstudy.com] On Behalf
> > Of
> > > Andy Tang
> > > Sent: Monday, June 27, 2005 9:13 PM
> > > To: Brian McGahan
> > > Cc: Chad Hintz; Mathew; Cisco certification
> > > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > >
> > > Hi Brian,
> > > Can I boot the enterprise plus image c2600-js-mz.122-15.T16.bin from
> > TFTP
> > > to the 2620 64MD/16F via the "tftpdnld -r" command in rommon?
> > > Thanks & regards,
> > > Andy
> > >
> > > On 5/25/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
> > > >
> > > > You can boot the 2600XM enterprise plus image from TFTP to the 2610
> > or
> > > > 2611 via the "tftpdnld -r" command in rommon.
> > > >
> > > > HTH,
> > > >
> > > > Brian McGahan, CCIE #8593
> > > > bmcgahan@internetworkexpert.com
> > > >
> > > > Internetwork Expert, Inc.
> > > > http://www.InternetworkExpert.com
> > > > Toll Free: 877-224-8987 x 705
> > > > Outside US: 775-826-4344 x 705
> > > > 24/7 Support: http://forum.internetworkexpert.com
> > > > Live Chat: http://www.internetworkexpert.com/chat/
> > > >
> > > >
> > > > > -----Original Message-----
> > > > > From: nobody@groupstudy.com [mailto: nobody@groupstudy.com] On
> > Behalf
> > > > Of
> > > > > Chad Hintz
> > > > > Sent: Tuesday, May 24, 2005 7:11 AM
> > > > > To: Mathew; 'Cisco certification'
> > > > > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > > > >
> > > > > The 2610 does not support this feature, you need a 2620 or 21 to
> > use
> > > > > ospfv3.
> > > > >
> > > > > HTH,
> > > > >
> > > > > Chad
> > > > >
> > > > >
> > > > > Hi Team
> > > > >
> > > > > Does anybody know why I can not enable IPV6 OSPF on 2600 with IOS
> > ver
> > > > > 12.2(15)T15?
> > > > >
> > > > > Even after configuring "ipv6 unicast-routing" and "ipv6 enable"
> > under
> > > > the
> > > > > interface, I do not see
> > > > >
> > > > > a OSPF option.
> > > > >
> > > > > Does anybody know why it is so?
> > > > >
> > > > > R2(config-if)#ipv6 ?
> > > > > IPv6 interface subcommands:
> > > > > address Configure IPv6 address on interface
> > > > > cef Cisco Express Forwarding for IPv6
> > > > > enable Enable IPv6 on interface
> > > > > mtu Set IPv6 Maximum Transmission Unit
> > > > > nat Enable IPv6 NAT on interface
> > > > > nd IPv6 interface Neighbor Discovery subcommands
> > > > > redirects Enable sending of ICMP Redirect messages
> > > > > rip Configure RIP routing protocol
> > > > > router IPv6 Router interface commands
> > > > > traffic-filter Access control list for packets
> > > > > unnumbered Preferred interface for source address selection
> > > > > verify Enable per packet validation
> > > > >
> > > > > R2(config-if)#ipv6 ro
> > > > > R2(config-if)#ipv6 router ?
> > > > > isis IS-IS Routing for IPv6
> > > > >
> > > > > R2(config-if)#ipv6 router
> > > > > R2(config-if)#do sho ver
> > > > > Cisco Internetwork Operating System Software
> > > > > IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T15,
> > RELEASE
> > > > > SOFTWARE (fc1)
> > > > > Technical Support: http://www.cisco.com/techsupport
> > > > > Copyright (c) 1986-2005 by cisco Systems, Inc.
> > > > > Compiled Thu 03-Mar-05 03:28 by hqluong
> > > > > Image text-base: 0x80008098, data-base: 0x81960D40
> > > > >
> > > > > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
> > > > > ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
> > > > SOFTWARE
> > > > > (fc1)
> > > > >
> > > > > R2 uptime is 47 minutes
> > > > > System returned to ROM by power-on
> > > > > System image file is "flash:c2600-j1s3-mz.122-15.T15.bin"
> > > > >
> > > > > cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K
> > bytes
> > > > of
> > > > > memory.
> > > > > Processor board ID JAD05090GQQ (1222274526)
> > > > > M860 processor: part number 0, mask 49
> > > > > Bridging software.
> > > > > X.25 software, Version 3.0.0.
> > > > > TN3270 Emulation software.
> > > > > 1 Ethernet/IEEE 802.3 interface(s)
> > > > > 2 Serial(sync/async) network interface(s)
> > > > > 16 terminal line(s)
> > > > > 32K bytes of non-volatile configuration memory.
> > > > > 16384K bytes of processor board System flash (Read/Write)
> > > > >
> > > > > Configuration register is 0x2102
> > > > >
> > > > > R2(config-if)#
> > > > >
> > > > >
> > > >
> > _______________________________________________________________________
> > > > > Subscription information may be found at:
> > > > > http://www.groupstudy.com/list/CCIELab.html
> > > > >
> > > > > __________________________________________________
> > > > > Do You Yahoo!?
> > > > > Tired of spam? Yahoo! Mail has the best spam protection around
> > > > > http://mail.yahoo.com
> > > > >
> > > > >
> > > >
> > _______________________________________________________________________
> > > > > Subscription information may be found at:
> > > > > http://www.groupstudy.com/list/CCIELab.html
> > > >
> > > >
> > _______________________________________________________________________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> > _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:00:29 GMT-3