From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Thu Sep 22 2005 - 13:57:42 GMT-3
Why would you need to do this? The metric will increment when the route
is received back automatically.
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: Edwards, Andrew M [mailto:andrew.m.edwards@boeing.com]
> Sent: Thursday, September 22, 2005 11:57 AM
> To: Brian McGahan; Easyman; GroupStudy CCIE-Lab
> Subject: RE: RIPng on NBMA issue
>
> To add to Brians post... Make sure you filter out the routes which you
> learn back from the hub you already know about.... IOW, manual
> split-hozizon.
>
> This is necessary because ipv6 split-horizon is a global proposition
to
> the router, not per link.
>
> HTH
>
> andy
>
> -----Original Message-----
> From: Brian McGahan [mailto:bmcgahan@internetworkexpert.com]
> Sent: Thursday, September 22, 2005 9:47 AM
> To: Easyman; GroupStudy CCIE-Lab
> Subject: RE: RIPng on NBMA issue
>
>
> Easyman,
>
> Split horizon for RIPng is controlled under the RIPng process
> with the "split-horizon" command, not at the interface level like in
> IPv4.
>
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Easyman
> > Sent: Thursday, September 22, 2005 10:11 AM
> > To: GroupStudy CCIE-Lab
> > Subject: RIPng on NBMA issue
> >
> > Hi , Groups
> >
> > Today I try to configure ripng on a frame-relay hub and spoke
network
> .
> >
> > Say R2 is the Hub, R4, R5, R6 are spoke routers .
> > Config as following
> >
> > R2
> > interface Serial0
> > ipv6 address 2003::150:50:100:2/96
> > ipv6 address FE80::2 link-local
> > ipv6 enable
> > ipv6 rip ripng2 enable
> > frame-relay map ipv6 FE80::4 104 broadcast
> > frame-relay map ipv6 FE80::5 105 broadcast
> > frame-relay map ipv6 FE80::6 106 broadcast
> > frame-relay map ipv6 2003::150:50:100:4 104 broadcast frame-relay
> > map ipv6 2003::150:50:100:5 105 broadcast frame-relay map ipv6
> > 2003::150:50:100:6 106 broadcast
> >
> > R4
> > Interface Serial0/0
> > ipv6 address 2003::150:50:100:4/96
> > ipv6 address FE80::4 link-local
> > ipv6 rip ripng2 enable
> > frame-relay map ipv6 FE80::2 401 broadcast
> > frame-relay map ipv6 FE80::5 401 broadcast
> > frame-relay map ipv6 FE80::6 401 broadcast
> > frame-relay map ipv6 2003::150:50:100:2 401 broadcast frame-relay
> > map ipv6 2003::150:50:100:5 401 broadcast frame-relay map ipv6
> > 2003::150:50:100:6 401 broadcast
> >
> >
> > R5
> > Interface Serial0
> > ipv6 address 2003::150:50:100:5/96
> > ipv6 address FE80::5 link-local
> > ipv6 rip ripng2 enable
> > frame-relay map ipv6 FE80::2 501 broadcast
> > frame-relay map ipv6 FE80::4 501 broadcast
> > frame-relay map ipv6 FE80::6 501 broadcast
> > frame-relay map ipv6 2003::150:50:100:2 501 broadcast frame-relay
> > map ipv6 2003::150:50:100:4 501 broadcast frame-relay map ipv6
> > 2003::150:50:100:6 501 broadcast
> >
> > R6
> > Interface serial0/0
> > ipv6 address 2003::150:50:100:6/96
> > ipv6 address FE80::6 link-local
> > ipv6 rip ripng2 enable
> > frame-relay map ipv6 FE80::2 601 broadcast
> > frame-relay map ipv6 FE80::4 601 broadcast
> > frame-relay map ipv6 FE80::5 601 broadcast
> > frame-relay map ipv6 2003::150:50:100:2 601 broadcast frame-relay
> > map ipv6 2003::150:50:100:4 601 broadcast frame-relay map ipv6
> > 2003::150:50:100:5 601 broadcast
> >
> >
> > On R2 I can received all the spoke router's lan ipv6 subnet routes.
> > And on all the spoke routers I have only R2's lan ipv6 subnet routes
,
> but
> > not any spoke's .
> >
> > Is there an split-horizon issue on R2 Serial 0 ?
> > I have tried to disable the split-horizon function on R2's Serial0 ,
> but I
> > can't find the command like such as "no ipv6 split-horizon" ?
> >
> > Someone please give me a hand.
> > TIA.
> >
> > Easyman
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sun Oct 02 2005 - 14:40:16 GMT-3