From: Rafay Aslam (smrafay@gmail.com)
Date: Sat Feb 25 2006 - 14:56:52 GMT-3
Hi
I am trying to setup trunk between my 2 Catalyst 5505s. I get this error
message when i try to enable trunk on my fast ethernet port. I want to know
if i can enable trunk on fastehternet ports on 5505s or it has to be fiber
ports on SUP III. Below is errors message, show ver and show module.
I tried enabling trunk of all of my ethernet module but got the same
message.
SW1 (enable) set trunk 2/13 on dot1q
Feature not supported on Module 2.
SW1 (enable)
SW1 (enable) set trunk 2/13 auto
Feature not supported on Module 2.
SW1 (enable)
SW1 (enable) sh ver
WS-C5505 Software, Version McpSW: 5.5(19) NmpSW: 5.5(19)
Copyright (c) 1995-2003 by Cisco Systems
NMP S/W compiled on Mar 27 2003, 17:53:27
MCP S/W compiled on Mar 27 2003, 17:47:48
System Bootstrap Version: 5.1(2)
Hardware Version: 1.0  Model: WS-C5505  Serial #: 066572009
Mod Port Model      Serial #  Versions
--- ---- ---------- --------- ----------------------------------------
1   2    WS-X5530   015926337 Hw : 3.4
                              Fw : 5.1(2)
                              Fw1: 4.4(1)
                              Sw : 5.5(19)
         WS-F5531   015735216 Hw : 2.0
         WS-U5533   015733996 Hw : 1.0
2   24   WS-X5224   022359370 Hw : 1.5
                              Fw : 3.1(1)
                              Sw : 5.5(19)
3   24   WS-X5224   022150757 Hw : 1.5
                              Fw : 3.1(1)
                              Sw : 5.5(19)
4   24   WS-X5224   022355793 Hw : 1.5
                              Fw : 3.1(1)
                              Sw : 5.5(19)
5   1    WS-X5302   019507332 Hw : 7.7
                              Fw : 20.22
                              Fw1: 3.1(1)
                              Sw : 12.2(32)
       DRAM                    FLASH                   NVRAM
Module Total   Used    Free    Total   Used    Free    Total Used  Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1       32768K  19667K  13101K   8192K   5629K   2563K  512K  172K  340K
Uptime is 0 day, 0 hour, 48 minutes
SW1 (enable)
SW1 (enable) show module
Mod Slot Ports Module-Type               Model               Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1   1    2     100BaseFX MMF Supervisor  WS-X5530            yes faulty
2   2    24    10/100BaseTX Ethernet     WS-X5224            no  ok
3   3    24    10/100BaseTX Ethernet     WS-X5224            no  ok
4   4    24    10/100BaseTX Ethernet     WS-X5224            no  ok
5   5    1     Route Switch              WS-X5302            no  ok
Mod Module-Name         Serial-Num
--- ------------------- --------------------
1                       00015926337
2                       00022359370
3                       00022150757
4                       00022355793
5                       00019507332
Mod MAC-Address(es)                        Hw     Fw         Sw
--- -------------------------------------- ------ ----------
-----------------
1   00-03-fe-6e-c0-00 to 00-03-fe-6e-c3-ff 3.4    5.1(2)     5.5(19)
2   00-01-c9-ac-ba-08 to 00-01-c9-ac-ba-1f 1.5    3.1(1)     5.5(19)
3   00-01-c9-ab-cf-a8 to 00-01-c9-ab-cf-bf 1.5    3.1(1)     5.5(19)
4   00-01-c9-ac-75-e0 to 00-01-c9-ac-75-f7 1.5    3.1(1)     5.5(19)
5   00-e0-1e-90-da-fe to 00-e0-1e-90-da-ff 7.7    20.22      12.2(32)
Mod Sub-Type Sub-Model Sub-Serial Sub-Hw
--- -------- --------- ---------- ------
1   NFFC II  WS-F5531  0015735216 2.0
1   uplink   WS-U5533  0015733996 1.0
SW1 (enable)
This archive was generated by hypermail 2.1.4 : Wed Mar 01 2006 - 11:28:18 GMT-3