From: Ivan Kuchin (ivan@iip.net)
Date: Fri Mar 03 2006 - 09:45:27 GMT-3
Mls qos is enabled. But sh int policy-map int is zero. 
I think that policing indicator must exist. 
Thank for help.
---------------------------------------------------------
Giga-LPI#show interfaces gigabitEthernet 0/18 capabilities | i Mode
  Model:                 WS-C2970G-24TS-E
Giga-LPI#show mls qos
QoS is enabled
Giga-LPI#show mls qos interface statistics | b 0/18
GigabitEthernet0/18
  dscp: incoming
-------------------------------
  0 -  4 :   191954176            0        10548            0       241903
  5 -  9 :           0         1595            0            0            0
 25 - 29 :           0          374            0            0            0
 45 - 49 :           0            0            0       430508            0
  dscp: outgoing
-------------------------------
  0 -  4 :   207682447            0            0            0            0
---------------------------------------------------------
> Ivan,
>
> Which switch are you working with?  On the 3550 you do not see hit counts
> from "show policy-map int,"  even when it is working.  To get some hint of
> operation, try "show mls qos interface statistics".  Your configuration
> looks good to me.  Remember you must enable mls qos globally for it to
> actually work:  show mls qos.
>
> HTH,
>
> Bob Sinclair
> CCIE #10427, CCSI 30427
> www.netmasterclass.net
>
>   ----- Original Message -----
>   From: Ivan
>   To: ccielab@groupstudy.com
>   Sent: Friday, March 03, 2006 7:08 AM
>   Subject: QOS policy
>
>
>   Hello !
>
>   Is it possible on L2-switch MQC-policing.
>   I'm configure the following:
>
>   class-map match-any ArtTelecomm
>     match access-group name ArtTelecomm
>   !
>   !
>   policy-map ArtTelecomm
>     class ArtTelecomm
>       police 512000 512000 exceed-action drop
>
>   interface GigabitEthernet0/18
>    description ArtTelecom
>    switchport access vlan 65
>    switchport mode access
>    switchport nonegotiate
>    service-policy input ArtTelecomm
>    speed 100
>   end
>
>   but it doesn't work.
>   Giga-LPI#sh policy-map interface
>    GigabitEthernet0/18
>
>     Service-policy input: ArtTelecomm
>
>       Class-map: ArtTelecomm (match-any)
>         0 packets, 0 bytes
>         5 minute offered rate 0 bps, drop rate 0 bps
>         Match: access-group name ArtTelecomm
>           0 packets, 0 bytes
>           5 minute rate 0 bps
>
>       Class-map: class-default (match-any)
>         0 packets, 0 bytes
>         5 minute offered rate 0 bps, drop rate 0 bps
>         Match: any
>           0 packets, 0 bytes
>           5 minute rate 0 bps
>
>
>   Any comments appreciate.
>
>   --
>   Ivan
>
>   _______________________________________________________________________
>   Subscription information may be found at:
>   http://www.groupstudy.com/list/CCIELab.html
-- iWAN kU^IN (mail to: ivan@iip.net) NOC iip.net 137-31-04
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:37 GMT-3