From: Wolfgang Marschner (wmarschner@web.de)
Date: Tue Mar 21 2006 - 09:35:58 GMT-3
Simply not enough DSPs available.
Have a look with the command s"how diag",
whether PVDM-12 modules are installed on the NM-HDV and/or
check with the command "test dsp 1" your DSPs.
For your E1 you need at least 3 x PVDM-12!
Regards
Wolfgang
CSSI #23525, CCIE #8232
----- Original Message -----
From: "amir cohen" <avi_patish@yahoo.com>
To: "FORUM" <ccielab@groupstudy.com>
Sent: Tuesday, March 21, 2006 1:16 PM
Subject: 2610XM voice card problem?
> Guys,
>
>
> I have a 2610XM with NMHDV-1e1 ,
> and when i am tryng to activate the command:
>
> Pri-group time-slot 1-31, i am getting
>
> " DSP Not enough DSP resources"
> You have 0 DSP for time slots
>
>
> here is the configuration:
>
>
> =========================
>
> SHOW VER:
> Yeruham#show controller e1
> E1 1/0 is up.
> Applique type is Channelized E1 - balanced
> No alarms detected.
> alarm-trigger is not set
> Version info Firmware: 20040802, FPGA: 255,
> spm_count = 0
> Framing is CRC4, Line Code is HDB3, Clock Source is
> Line.
> Current port master clock:recovered from controller
> 1/0
> Data in current interval (138 seconds elapsed):
> 0 Line Code Violations, 0 Path Code Violations
> 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0
> Degraded Mins
> 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err
> Secs, 0 Unavail Secs
> Total Data (last 24 hours)
> 257564 Line Code Violations, 5834 Path Code
> Violations,
> 3 Slip Secs, 4 Fr Loss Secs, 12 Line Err Secs, 2
> Degraded Mins,
> 9 Errored Secs, 0 Bursty Err Secs, 5 Severely Err
> Secs, 84192 Unavail Secs
> Yeruham#show ver
> Cisco IOS Software, C2600 Software
> (C2600-ADVENTERPRISEK9_IVS-M), Version 12.4(5
> a), RELEASE SOFTWARE (fc3)
> Technical Support: http://www.cisco.com/techsupport
> Copyright (c) 1986-2006 by Cisco Systems, Inc.
> Compiled Fri 13-Jan-06 19:19 by alnguyen
>
> ROM: System Bootstrap, Version 12.2(8r) [cmong 8r],
> RELEASE SOFTWARE (fc1)
>
> Yeruham uptime is 1 week, 5 days, 16 hours, 3 minutes
> System returned to ROM by reload
> System image file is
> "flash:c2600-adventerprisek9_ivs-mz.124-5a.bin"
>
>
> This product contains cryptographic features and is
> subject to United
> States and local country laws governing import,
> export, transfer and
> use. Delivery of Cisco cryptographic products does not
> imply
> third-party authority to import, export, distribute or
> use encryption.
> Importers, exporters, distributors and users are
> responsible for
> compliance with U.S. and local country laws. By using
> this product you
> agree to comply with applicable laws and regulations.
> If you are unable
> to comply with U.S. and local laws, return this
> product immediately.
>
> A summary of U.S. laws governing Cisco cryptographic
> products may be found at:
> http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
>
> If you require further assistance please contact us by
> sending email to
> export@cisco.com.
>
> Cisco 2610XM (MPC860P) processor (revision 4.1) with
> 124005K/7067K bytes of memo
> ry.
> Processor board ID FTX1002C03G
> M860 processor: part number 5, mask 2
> 1 FastEthernet interface
> 2 Low-speed serial(sync/async) interfaces
> 1 Channelized E1/PRI port
> 32K bytes of NVRAM.
> 32768K bytes of processor board System flash
> (Read/Write)
>
> ========================================
>
> Configuration:
>
>
> ===============
> Current configuration : 1464 bytes
> !
> version 12.4
> service timestamps debug datetime msec
> service timestamps log datetime msec
> no service password-encryption
> !
> hostname XXXX
> !
> boot-start-marker
> boot-end-marker
> !
> card type e1 1 1
> enable password team1$
> !
> no aaa new-model
> !
> resource policy
> !
> no network-clock-participate slot 1
> no network-clock-participate wic 0
> ip cef
> !
> !
> !
> !
> !
> !
> !
> isdn switch-type primary-net5
> voice-card 1
> dsp services dspfarm
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> controller E1 1/0
> !
> !
> !
> !
> interface Loopback0
> ip address 192.168.253.253 255.255.255.255
> !
> interface FastEthernet0/0
> ip address 172.17.8.240 255.255.0.0 secondary
> ip address 172.17.100.50 255.255.0.0
> duplex auto
> speed auto
> !
> interface Serial0/0
> description Connection to the XXXXX
> ip address 172.31.17.2 255.255.255.0
> no dce-terminal-timing-enable
> !
> !
> !
> !
> no ip http server
> no ip http secure-server
> !
> !
> !
> !
> control-plane
> !
> !
> !
> !
> !
> !
> !
> !
> !
> !
> gatekeeper
> shutdown
> !
>
> !
> end
>
>
> ===============================
>
>
> Anu IDEAS:-)
>
>
> Amir
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:39 GMT-3