From: amir cohen (avi_patish@yahoo.com)
Date: Tue Mar 28 2006 - 06:03:54 GMT-3
Here is the debug output taking from the CISCO 2610XM
gateway:
================
Mar 27 11:59:59 10.33.158.88 39457: sinvgw: Mar 27
17:57:21.533: %SYS-5-CONFIG_I: Configured from console
by i027201 on vty5 (10.33.142.12)
Mar 27 12:00:13 10.33.158.88 39458: sinvgw: Mar 27
17:57:35 GMT: ISDN Se1/0:15 Q931: TX -> SETUP pd = 8
callref = 0x20EB
Mar 27 12:00:13 10.33.158.88 39459: sinvgw: Sending
Complete
Mar 27 12:00:13 10.33.158.88 39460: sinvgw: Bearer
Capability i = 0x9090A3
Mar 27 12:00:13 10.33.158.88 39461: sinvgw: Standard
= CCITT
Mar 27 12:00:13 10.33.158.88 39462: sinvgw: Transer
Capability = 3.1kHz Audio
Mar 27 12:00:13 10.33.158.88 39463: sinvgw: Transfer
Mode = Circuit
Mar 27 12:00:13 10.33.158.88 39464: sinvgw: Transfer
Rate = 64 kbit/s
Mar 27 12:00:13 10.33.158.88 39465: sinvgw: Channel
ID i = 0xA98381
Mar 27 12:00:13 10.33.158.88 39466: sinvgw:
Exclusive, Channel 1
Mar 27 12:00:13 10.33.158.88 39467: sinvgw: Progress
Ind i = 0x8183 - Origination address is non-ISDN
Mar 27 12:00:13 10.33.158.88 39468: sinvgw: Display i
= 'AMIR C'
Mar 27 12:00:13 10.33.158.88 39469: sinvgw: Calling
Party Number i = 0x80, '8161900'
Mar 27 12:00:13 10.33.158.88 39470: sinvgw:
Plan:Unknown, Type:Unknown
Mar 27 12:00:13 10.33.158.88 39471: sinvgw: Called
Party Number i = 0x80, '6521'
Mar 27 12:00:13 10.33.158.88 39472: sinvgw:
Plan:Unknown, Type:Unknown
Mar 27 12:00:13 10.33.158.88 39473: sinvgw: Mar 27
17:57:35 GMT: ISDN Se1/0:15 Q931: RX <- CALL_PROC pd =
8 callref = 0xA0EB
Mar 27 12:00:13 10.33.158.88 39474: sinvgw: Channel
ID i = 0xA98381
Mar 27 12:00:13 10.33.158.88 39475: sinvgw:
Exclusive, Channel 1
Mar 27 12:00:14 10.33.158.88 39476: sinvgw: Mar 27
17:57:35 GMT: ISDN Se1/0:15 Q931: RX <- ALERTING pd =
8 callref = 0xA0EB
Mar 27 12:00:14 10.33.158.88 39477: sinvgw: Facility
i =
0x91AA068001008201008B0100A11B0202010006042B0C0901800F4552414E20474F4C44454E42455247
Mar 27 12:00:14 10.33.158.88 39478: sinvgw: Locking
Shift to Codeset 5
Mar 27 12:00:14 10.33.158.88 39479: sinvgw: Codeset 5
IE 0x32 i = 0x81
Mar 27 12:00:25 10.33.158.88 39480: sinvgw: Mar 27
17:57:46 GMT: ISDN Se1/0:15 Q931: RX <- CONNECT pd = 8
callref = 0xA0EB
Mar 27 12:00:25 10.33.158.88 39481: sinvgw: Facility
i =
0x91AA068001008201008B0100A1190202010006042B0C0902800D4D4552494449414E204D41494C
Mar 27 12:00:25 10.33.158.88 39482: sinvgw: Progress
Ind i = 0x8182 - Destination address is non-ISDN
Mar 27 12:00:25 10.33.158.88 39483: sinvgw: Connected
Number i = 0x0080, '6777'
Mar 27 12:00:25 10.33.158.88 39484: sinvgw: Locking
Shift to Codeset 5
Mar 27 12:00:25 10.33.158.88 39485: sinvgw: Codeset 5
IE 0x32 i = 0x81
Mar 27 12:00:25 10.33.158.88 39486: sinvgw: Mar 27
17:57:46 GMT: ISDN Se1/0:15 Q931: TX -> CONNECT_ACK pd
= 8 callref = 0x20EB
Mar 27 12:00:25 10.33.158.88 39487: sinvgw: Mar 27
17:57:48.074: %ISDN-6-CONNECT: Interface Serial1/0:0
is now connected to 6521 unknown
Mar 27 12:00:25 10.33.158.88 39488: sinvgw: Mar 27
17:57:48.074: %ISDN-6-DISCONNECT: Interface
Serial1/0:0 disconnected from 6521 , call lasted 1
seconds
Mar 27 12:00:26 10.33.158.88 39489: sinvgw: Mar 27
17:57:48 GMT: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd
= 8 callref = 0x20EB
Mar 27 12:00:26 10.33.158.88 39490: sinvgw: Cause i =
0x8290 - Normal call clearing
Mar 27 12:00:26 10.33.158.88 39491: sinvgw: Mar 27
17:57:48 GMT: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8
callref = 0xA0EB
Mar 27 12:00:26 10.33.158.88 39492: sinvgw: Mar 27
17:57:48 GMT: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP
pd = 8 callref = 0x20EB
Mar 27 12:00:32 10.33.158.88 39493: sinvgw: Mar 27
17:57:54 GMT: ISDN Se1/0:15 Q931: TX -> SETUP pd = 8
call
--- amir cohen <avi_patish@yahoo.com> wrote:
> Guys,
>
> I need your input for a "starnge" problem that i am
> having:
>
> ===========
>
> i have 2 H323 gateways:
>
> 1. cisco 2610XM
> 2. AVYA IP call Center
>
> the cisco 2610XM has a PRI toward the PBX(nortel
> Merdian), it is working !!!!!!
> BUT,
>
> When i am dialing from one phone to the another
> phone,
> all i am seeing is the Caller Number NOT the name:
>
> I did a debug ISDN q931 int the 2610XM:
> AND i saw:
>
> a packet coming from the AVAYA has a field called
> DISPLAY IE with the NAME of the caller,
>
> But the PBX is not getting it.
>
> WHY?
>
> DO you know another way to send the display name????
>
>
> Thanx,
> Amir
>
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam
> protection around
> http://mail.yahoo.com
>
>
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:40 GMT-3