From: Keith Bizzell (mkbcoolman@gmail.com)
Date: Mon Jan 08 2007 - 17:43:56 ART
Doh! That was it. I added to dialer list and bounced the serial interfaces
and now it works. It's always something simple.
Thanks Nick!
Keith
On 1/8/07, Nick Griffin <nick.jon.griffin@gmail.com> wrote:
>
> How about:
>
> dialer-list 1 protocol ip permit
>
> On 1/8/07, Keith Bizzell <mkbcoolman@gmail.com> wrote:
>
> > This section calls for creating a ppp link between R4/R5 using dialer
> > interfaces. This seems pretty straight-forward, and as far as I can
> > tell my
> > config matches up with the solution guide. But it doesn't work. R4
> > never
> > shows an active call, and I never get an bind message. Interfaces show
> > up/up on both sides, and I know there isn't a problem with the link (it
> > works fine when I set up ppp on the physical interface.) Any ideas?
> >
> > R4:
> > interface Serial0/1/0
> > no ip address
> > dialer in-band
> > dialer pool-member 1
> > pulse-time 1
> > !
> > interface Dialer0
> > ip address 128.1.45.4 255.255.255.0
> > encapsulation ppp
> > dialer pool 1
> > dialer idle-timeout 0
> > dialer persistent
> > !
> > Rack1R4(config-if)#do show ip int b
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/0 128.1.14.4 YES NVRAM up
> > up
> > FastEthernet0/1 128.1.48.4 YES NVRAM up
> > up
> > Serial0/0/0 unassigned YES NVRAM administratively
> > down
> > down
> > Serial0/1/0 unassigned YES NVRAM up
> > up
> > Dialer0 128.1.45.4 YES manual up
> > up
> > Loopback0 150.1.4.4 YES NVRAM up
> > up
> >
> > Rack1R4(config-if)#do show dialer
> >
> > Se0/1/0 - dialer type = IN-BAND SYNC NO-PARITY
> > Dialer pool 1, priority 0
> > Idle timer (120 secs), Fast idle timer (20 secs)
> > Wait for carrier (30 secs), Re-enable (15 secs)
> > Dialer state is idle
> >
> > Di0 - dialer type = DIALER PROFILE
> > Idle timer (never), Fast idle timer (20 secs)
> > Wait for carrier (30 secs), Re-enable (15 secs)
> > Dialer state is idle
> > Number of active calls = 0
> >
> > Dial String Successes Failures Last DNIS Last status
> >
> > R5:
> >
> > interface Serial0/1/0
> > no ip address
> > dialer in-band
> > dialer pool-member 1
> > clock rate 64000
> > pulse-time 1
> > !
> > interface Virtual-Template1
> > ip address 128.1.125.5 255.255.255.0
> > !
> > interface Dialer0
> > ip address 128.1.45.5 255.255.255.0
> > encapsulation ppp
> > dialer pool 1
> > dialer idle-timeout 0
> > dialer persistent
> > !
> > Rack1R5(config-if)#do show dialer
> >
> > Se0/1/0 - dialer type = IN-BAND SYNC NO-PARITY
> > Dialer pool 1, priority 0
> > Idle timer (never), Fast idle timer (20 secs)
> > Wait for carrier (30 secs), Re-enable (15 secs)
> > Dialer state is data link layer up
> > Interface bound to profile Di0
> > Time until disconnect never
> > Connected to <unknown phone number>
> >
> > Di0 - dialer type = DIALER PROFILE
> > Idle timer (never), Fast idle timer (20 secs)
> > Wait for carrier (30 secs), Re-enable (15 secs)
> > Dialer state is data link layer up
> > Number of active calls = 1
> >
> > Dial String Successes Failures Last DNIS Last status
> > Rack1R5(config-if)#do show ip int b
> > Interface IP-Address OK? Method Status
> > Protocol
> > FastEthernet0/0 unassigned YES unset administratively
> > down
> > down
> > FastEthernet0/1 128.1.5.5 YES manual up
> > up
> > Serial0/0/0 unassigned YES unset up
> > up
> > Serial0/0/0.1 unassigned YES unset up
> > up
> > Serial0/1/0 unassigned YES TFTP up
> > up
> > Virtual-Access1 unassigned YES unset down
> > down
> > Virtual-Template1 128.1.125.5 YES manual down
> > down
> > Virtual-Access2 128.1.125.5 YES TFTP up
> > up
> > Virtual-Access3 128.1.125.5 YES TFTP up
> > up
> > Dialer0 128.1.45.5 YES manual up
> > up
> > Loopback0 150.1.5.5 YES manual up
> > up
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Feb 08 2007 - 23:46:56 ART