From: Michael Zuo (mzuo@ixiacom.com)
Date: Fri Feb 02 2007 - 03:09:21 ART
Hi Group,
I could not get my IPv6 routes to redistribute among various RIP
processes. Seems simple enough but I just can not get it to work? Please
help,
Thanks a lot ....
R1(config-rtr)#do sh run | be ipv6 router
ipv6 router rip FRAME-123
redistribute rip FRAME-14 metric 1
redistribute rip FRAME-16 metric 1
no split-horizon
!
ipv6 router rip FRAME-14
redistribute rip FRAME-123 metric 1
redistribute rip FRAME-16 metric 1
!
ipv6 router rip FRAME-16
redistribute rip FRAME-123 metric 1
redistribute rip FRAME-14 metric 1
!
!
R1(config-rtr)#do sh ipv6 rip da
RIP process "FRAME-123", local RIB
FEC0::A:0:0:7B:0/125, metric 2
Serial0/0.1/FE80::7B:2, expires in 163 secs
Serial0/0.1/FE80::7B:3, expires in 165 secs
FEC0::B:0:0:67:1/128, metric 2, installed
Serial0/0.1/FE80::7B:3, expires in 165 secs
RIP process "FRAME-14", local RIB
FEC0::B:0:0:E:0/125, metric 2
Serial0/0.2/FE80::7B:4, expires in 155 secs
RIP process "FRAME-16", local RIB
FEC0::B:0:0:10:0/125, metric 2
Ethernet0/0/FE80::16:6, expires in 174 secs
R1(config-rtr)#do sh ipv6 int s0/0.1
Serial0/0.1 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::7B:1
Global unicast address(es):
FEC0::A:0:0:7B:1, subnet is FEC0::A:0:0:7B:0/125
Joined group address(es):
FF02::1
FF02::2
FF02::9
FF02::1:FF7B:1
MTU is 1500 bytes
ICMP error messages limited to one every 100 milliseconds
ICMP redirects are enabled
ND DAD is not supported
ND reachable time is 30000 milliseconds
Hosts use stateless autoconfig for addresses.
R1(config-rtr)#do sh ipv6 int s0/0.2
Serial0/0.2 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::7B:14
Global unicast address(es):
FEC0::B:0:0:E:1, subnet is FEC0::B:0:0:E:0/125
Joined group address(es):
FF02::1
FF02::2
FF02::9
FF02::1:FF0E:1
FF02::1:FF7B:14
MTU is 1500 bytes
ICMP error messages limited to one every 100 milliseconds
ICMP redirects are enabled
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
Hosts use stateless autoconfig for addresses.
R1(config-rtr)#do sh ipv6 int e0/0
Ethernet0/0 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::16:1
Global unicast address(es):
FEC0::B:0:0:10:1, subnet is FEC0::B:0:0:10:0/125
Joined group address(es):
FF02::1
FF02::2
FF02::9
FF02::1:FF10:1
FF02::1:FF16:1
MTU is 1500 bytes
ICMP error messages limited to one every 100 milliseconds
ICMP redirects are enabled
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds
ND advertised reachable time is 0 milliseconds
ND advertised retransmit interval is 0 milliseconds
ND router advertisements are sent every 200 seconds
ND router advertisements live for 1800 seconds
Hosts use stateless autoconfig for addresses.
R1(config-rtr)#
My Configuration is:
ipv6 unicast-routing
interface Ethernet0/0
ip address 172.16.16.1 255.255.255.0
ip pim dense-mode
ip ospf hello-interval 5
half-duplex
ipv6 address FEC0::B:0:0:10:1/125
ipv6 address FE80::16:1 link-local
ipv6 rip FRAME-16 enable
standby 1 ip 172.16.16.254
standby 1 priority 110
standby 1 preempt
standby 1 authentication doitlab1
standby 1 name 3000
!
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 multipoint
ip address 172.16.123.1 255.255.255.0
ip pim dense-mode
ip ospf network non-broadcast
ipv6 address FEC0::A:0:0:7B:1/125
ipv6 address FE80::7B:1 link-local
ipv6 rip FRAME-123 enable
frame-relay map ipv6 FEC0::A:0:0:7B:2 102 broadcast
frame-relay map ipv6 FEC0::A:0:0:7B:3 103 broadcast
frame-relay map ip 172.16.123.2 102 broadcast
frame-relay map ip 172.16.123.3 103 broadcast
frame-relay map ipv6 FE80::7B:2 102 broadcast
frame-relay map ipv6 FE80::7B:3 103 broadcast
frame-relay interface-dlci 102
no frame-relay inverse-arp
service-policy input HTTP
!
interface Serial0/0.2 point-to-point
ip address 172.16.14.1 255.255.255.0
ip pim dense-mode
ip ospf network point-to-point
ipv6 address FEC0::B:0:0:E:1/125
ipv6 address FE80::7B:14 link-local
ipv6 rip FRAME-14 enable
frame-relay interface-dlci 104
This archive was generated by hypermail 2.1.4 : Thu Mar 01 2007 - 07:38:45 ART