From: Kim (support@isolvesystems.com)
Date: Tue May 29 2007 - 18:35:10 ART
Sadiq,
I think you can use just one virtual-template on R5. It will create two
virtual-access interface.
I ran into some issues doing it your way when I configured OSPF.
Kim
On 5/29/07, Sadiq Yakasai <sadiqtanko@gmail.com> wrote:
>
> i tried it again and this time ur way, and it works fine!
> see below my config:
> R1---------\
> \
> /-----------R5
> R2---------/
>
>
> -------------------------------------------------------------------------------------------------------------
> R5#sh run
> hostname R5
> !
> interface Serial0/1/0
> no ip address
> encapsulation frame-relay
> frame-relay interface-dlci 501 ppp Virtual-Template1
> frame-relay interface-dlci 502 ppp Virtual-Template2
> !
> interface Virtual-Template1
> ip address 192.168.1.5 255.255.255.0
> !
> interface Virtual-Template2
> ip address 192.168.1.5 255.255.255.0
>
> end
>
> --------------------------------------------------------------------------------------------------
>
> R1#sh run
> Building configuration...
>
> interface Serial0/1/0
> no ip address
> encapsulation frame-relay
> frame-relay interface-dlci 105 ppp Virtual-Template1
> !
> interface Virtual-Template1
> ip address 192.168.1.1 255.255.255.0
> !
> end
>
> R1#
>
>
> ---------------------------------------------------------------------------------------------------
> R2#sh run
> Building configuration...
>
> interface Serial0/1/0
> no ip address
> encapsulation frame-relay
> frame-relay interface-dlci 205 ppp Virtual-Template1
> !
> interface Virtual-Template1
> ip address 192.168.1.2 255.255.255.0
> !
> end
>
> R2#
>
>
>
> -----------------------------------------------------------------------------------------------------
> Successful Pings!!
>
> R2#ping 192.168.1.1
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60 ms
>
> R2#ping 192.168.1.5
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.168.1.5, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 28/29/32 ms
>
>
> I think u need to check ur other spoke router's config!!
>
> HTH
>
> Sadiq
>
>
> On 5/29/07, Sadiq Yakasai <sadiqtanko@gmail.com> wrote:
> >
> > hey there,
> >
> > dont u need to configure another dlci's on the two spoke routers,
> pointing to each other?
> >
> > I tried that and it seems to work fine.
> >
> >
> >
> > On 5/29/07, ccie anees <ccieanees@yahoo.com> wrote:
> > > I have an issue in pinging between spoke routers.
> > > R3 is a hub router.
> > >
> > > ------ R1
> > > |
> > > R3 ---
> > > |
> > > ------ R5
> > >
> > > R3
> > > interface Serial1/0
> > > no ip address
> > > encapsulation frame-relay IETF
> > > frame-relay interface-dlci 301 ppp Virtual-Template13
> > > frame-relay interface-dlci 305 ppp Virtual-Template35
> > > no frame-relay inverse-arp
> > > !
> > > interface Virtual-Template13
> > > ip address 167.1.135.3 255.255.255.0
> > > !
> > > interface Virtual-Template35
> > > ip address 167.1.135.3 255.255.255.0
> > > !
> > > router eigrp 10
> > > network 167.1.135.3 0.0.0.0
> > > no auto-summary
> > > eigrp router-id 150.1.3.3
> > > R1
> > > interface Serial0/0
> > > no ip address
> > > encapsulation frame-relay
> > > frame-relay interface-dlci 103 ppp Virtual-Template13
> > > no frame-relay inverse-arp
> > > !
> > > interface Virtual-Template13
> > > ip address 167.1.135.1 255.255.255.0
> > > !
> > > router eigrp 10
> > > network 167.1.135.1 0.0.0.0
> > > no auto-summary
> > > eigrp router-id 150.1.1.1
> > >
> > > R5
> > > interface Serial0/0
> > > no ip address
> > > encapsulation frame-relay IETF
> > > frame-relay interface-dlci 503 ppp Virtual-Template35
> > > no frame-relay inverse-arp
> > > !
> > > interface Virtual-Template35
> > > ip address 167.1.135.5 255.255.255.0
> > > !
> > > router eigrp 10
> > > network 167.1.135.5 0.0.0.0
> > > no auto-summary
> > > eigrp router-id 150.1.5.5
> > >
> > > Result:
> > > R3:
> > > Rack1R3#ping 167.1.135.1
> > > Type escape sequence to abort.
> > > Sending 5, 100-byte ICMP Echos to 167.1.135.1, timeout is 2 seconds:
> > > !!!!!
> > > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/60
> ms
> > > Rack1R3#ping 167.1.135.5
> > > Type escape sequence to abort.
> > > Sending 5, 100-byte ICMP Echos to 167.1.135.5, timeout is 2 seconds:
> > > !!!!!
> > > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60
> ms
> > > Rack1R3#
> > >
> > > Problem:
> > > R5
> > >
> > > Rack1R5#ping 167.1.135.3
> > > Type escape sequence to abort.
> > > Sending 5, 100-byte ICMP Echos to 167.1.135.3, timeout is 2 seconds:
> > > !!!!!
> > > Success rate is 100 percent (5/5), round-trip min/avg/max = 56/59/60
> ms
> > > Rack1R5#
> > >
> > > Rack1R5#ping 167.1.135.1
> > > Type escape sequence to abort.
> > > Sending 5, 100-byte ICMP Echos to 167.1.135.1, timeout is 2 seconds:
> > > .....
> > > Success rate is 0 percent (0/5)
> > >
> > >
> > > ---------------------------------
> > > Luggage? GPS? Comic books?
> > > Check out fitting gifts for grads at Yahoo! Search.
> > >
> > >
> _______________________________________________________________________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
-- http://www.isolvesystems.com
This archive was generated by hypermail 2.1.4 : Fri Jun 01 2007 - 06:55:22 ART