From: subodh.rawat@wipro.com
Date: Wed Jul 25 2007 - 07:06:43 ART
Guys.....I am not going to work on it any more now. I will again work on
it at home after office hours...will let you know my result tomorrow.
Still my doubt is on Dynamips....I will change some configuration
settings (although existing seems perfect). Currently, I am running both
swtches on two different UDP ports 7200 and 7201. I will get them to
single port and will see it.
Wish me guys.
Regards
Subodh
________________________________
From: Subodh Singh Rawat (WT01 - TELECOM SERVICE PROVIDER)
Sent: Wednesday, July 25, 2007 3:20 PM
To: 'Mounir Mohamed'
Cc: djerk@djerk.nl; tohsoon28@gmail.com; ccielab@groupstudy.com
Subject: RE: Basic switching trunking question..please answer
I am lost guys.....I have everything corerct...created vlan 3 from vlan
database. int vlan 3 is up,up......cdp is showing other switch
information...trunk is correct...
Now since Mounir's configuration is working absolutely fine......I think
I am not gonna sleep properly tonight.
Regards
Subodh
________________________________
From: Mounir Mohamed [mailto:mounir.mohamed@gmail.com]
Sent: Wednesday, July 25, 2007 3:14 PM
To: Subodh Singh Rawat (WT01 - TELECOM SERVICE PROVIDER)
Cc: djerk@djerk.nl; tohsoon28@gmail.com; ccielab@groupstudy.com
Subject: Re: Basic switching trunking question..please answer
[mounir@unix-l1]$ more test.net
autostart=false
[localhost:7500]
[[3640]]
image = /home/mounir/image/c3640-js-mz.124-10a.image
ram = 128
disk0 = 0
disk1 = 0
[[Router sw1]]
idlepc = 0x604ec820
model = 3640
console = 2007
autostart = false
slot1 = NM-16ESW
F1/7 = sw2 f1/7
[[Router sw2]]
idlepc = 0x604ec820
model = 3640
console = 2008
autostart = false
slot1 = NM-16ESW
On 7/25/07, subodh.rawat@wipro.com <subodh.rawat@wipro.com> wrote:
Please can u share ur .Net file? I have connected on F1/7 of Sw1
to Sw2 F1/7 and I think this only required.
Mine is below:
[[Router SW1]]
model = 3640
console = 2007
autostart = False
slot0 = NM-16ESW
slot1 = NM-16ESW
F1/7 = SW2 F1/7
[[Router SW2]]
model = 3640
console = 2008
autostart = False
slot0 = NM-16ESW
slot1 = NM-16ESW
Regards
Subodh
________________________________
From: Mounir Mohamed [mailto:mounir.mohamed@gmail.com ]
Sent: Wednesday, July 25, 2007 2:55 PM
To: Subodh Singh Rawat (WT01 - TELECOM SERVICE PROVIDER)
Cc: djerk@djerk.nl; tohsoon28@gmail.com; ccielab@groupstudy.com
Subject: Re: Basic switching trunking question..please answer
Dear Subodh,
Am also uploded ur config to 2 switches on dynagen and everthing
working fine, erase ur config and do it again.
sw1#show run int f1/7
Building configuration...
Current configuration : 56 bytes
!
interface FastEthernet1/7
switchport mode trunk
end
sw1#show run int vlan 3
Building configuration...
Current configuration : 57 bytes
!
interface Vlan3
ip address 3.3.3.1 <http://3.3.3.1/> 255.255.255.0
<http://255.255.255.0/>
end
sw1#show vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 6
VTP Operating Mode : Server
VTP Domain Name : cisco
sw1#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- ---------
-------------------------------
1 default active Fa1/0, Fa1/1,
Fa1/2, Fa1/3
Fa1/4, Fa1/5,
Fa1/6, Fa1/8
Fa1/9, Fa1/10,
Fa1/11, Fa1/12
Fa1/13, Fa1/14,
Fa1/15
3 VLAN0003 active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode
Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- --------
------ ------
1 enet 100001 1500 - - - - -
1002 1003
3 enet 100003 1500 - - - - -
0 0
sw1#telnet 3.3.3.2 <http://3.3.3.2/>
Trying 3.3.3.2 <http://3.3.3.2/> ... Open
User Access Verification
Password:
sw2>ena
Password:
sw2#show run int f1/7
Building configuration...
Current configuration : 56 bytes
!
interface FastEthernet1/7
switchport mode trunk
sw2#show run int vlan 3
Building configuration...
Current configuration : 57 bytes
!
interface Vlan3
ip address 3.3.3.2 <http://3.3.3.2/> 255.255.255.0
<http://255.255.255.0/>
end
sw2#show vtp stat
sw2#show vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 6
VTP Operating Mode : Client
VTP Domain Name : cisco
sw2#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- ---------
-------------------------------
1 default active Fa1/0, Fa1/1,
Fa1/2, Fa1/3
Fa1/4, Fa1/5,
Fa1/6, Fa1/8
Fa1/9, Fa1/10,
Fa1/11, Fa1/12
Fa1/13, Fa1/14,
Fa1/15
3 VLAN0003 active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
Best Regards,
Mounir Mohamed
On 7/25/07, subodh.rawat@wipro.com < subodh.rawat@wipro.com
<mailto:subodh.rawat@wipro.com> > wrote:
sw1#sh int fa1/7 switchport
Name: Fa1/7
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1,3
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
sw2#sh int fa1/7 switchport
Name: Fa1/7
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1,3
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
-----Original Message-----
From: Djerk Geurts [mailto:djerk@djerk.nl]
Sent: Wednesday, July 25, 2007 2:18 PM
To: 'Toh Soon, Lim'; Subodh Singh Rawat (WT01 - TELECOM
SERVICE
PROVIDER)
Cc: ccielab@groupstudy.com
Subject: RE: Basic switching trunking question..please
answer
Add the following to the list from both switches:
- sh int f0/7 switch
> -----Original Message-----
> From: nobody@groupstudy.com
[mailto:nobody@groupstudy.com] On Behalf
> Of Toh Soon, Lim
> Sent: woensdag 25 juli 2007 7:34
> To: subodh.rawat@wipro.com
> Cc: ccielab@groupstudy.com
> Subject: Re: Basic switching trunking question..please
answer
>
> Hi Subodh,
>
> Your configs look fine to me. This simple setup should
work without
> issue.
>
> Anyway, can you provide us outputs of the following
commands:
>
> - sh ip arp vl 3
> - sh spann vl 3
> - sh int status
> - sh int trunk
>
>
> Thank you.
>
> B.Rgds,
> Lim TS
>
>
> On 7/25/07, subodh.rawat@wipro.com <
subodh.rawat@wipro.com <mailto:subodh.rawat@wipro.com> > wrote:
> >
> > Hi Champs,
> >
> > A basic switching problem I am facing. Please see
the diagram below:
> >
> >
> > --- f1/7 f1/7 ---
> > |sw1|--------------------------------|sw2|
> > --- dot1Q Trunk ---
> >
> >
> > Switch 1 is VTp Server with domain CISCO Switch 2 is
VTP Client with
> > domain CISCO port f1/7 is configured as Dot1q
encapsulation on both
> > the switches.
> > Only one VLAN, i.e. VLAN 3 is added on Sw1 and Same
is
> reflected in Sw2
> > too when I see "show vtp status"
> > and "show vlan brief" command. Please note that this
VLAn is not
> > associated with any physical interface of switch.
> >
> > When I see "sh int fa1/7 trunk" on both the
switches, it shows as
> > trunking with dot1q encapsulation.
> >
> > IP address of VLAn 3 on SW1 is 3.3.3.1/24 while on
sw2 is
> 3.3.3.2/24.
> >
> > "sh ip int br" also shows up,up for fa1/7 and vlan
3.
> >
> > I am not able to ping 3.3.3.1 <http://3.3.3.1/>
from sw2 and 3.3.3.2 <http://3.3.3.2/> from
> sw1. However, I
> > can ping Ip of own switch, i.e. 3.3.3.2
<http://3.3.3.2/> from sw2 and
> 3.3.3.1 <http://3.3.3.1/> from sw1.
> >
> > Can somebody tell me what is wrong with my
configuration?
> >
> > Another good thing is that, when I see "show cdp
entry *"
> from either
> > switches, it shows information about other switch.
e.g.
> when I see "show
> > cdp entry *" from sw1, it shows IP address of
3.3.3.2 <http://3.3.3.2/> (of
> sw2) in its
> > CDP database. It means layer 2 is working perfect
and
> trunking is also
> > perfect. Trunking is working fine can be verified
from the
> result that
> > VLAN 3 is present on sw2 which is VTP client for
CISCO VTP domain.
> >
> > I am not sure why I am not able to ping VLAN 3 IP
address
> of each other
> > switches.
> >
> >
> >
> > My configuration is below:
> >
> > Sw1
> > interface FastEthernet1/7
> > switchport trunk encapsulation dot1q switchport mode
trunk !
> > interface Vlan3
> > ip address 3.3.3.1 <http://3.3.3.1/> 255.255.255.0
<http://255.255.255.0/>
> >
> > Sw2
> > interface FastEthernet1/7
> > switchport trunk encapsulation dot1q
> > switchport mode trunk
> > !
> > interface Vlan3
> > ip address 3.3.3.2 <http://3.3.3.2/> 255.255.255.0
<http://255.255.255.0/>
> >
> >
> > CDP output:
> > sw1#sh cdp entry *
> > -------------------------
> > Device ID: sw2
> > Entry address(es):
> > IP address: 3.3.3.2 <http://3.3.3.2/>
> > Platform: Cisco 3640, Capabilities: Router Switch
IGMP
> > Interface: FastEthernet1/7, Port ID (outgoing
port):
> FastEthernet1/7
> > Holdtime : 128 sec
> >
> > Version :
> > Cisco IOS Software, 3600 Software (C3640-IS-M),
Version
> 12.4(8), RELEASE
> > SOFTWAR
> > E (fc1)
> > Technical Support: http://www.cisco.com/techsupport
> > Copyright (c) 1986-2006 by Cisco Systems, Inc.
> > Compiled Mon 15-May-06 16:27 by prod_rel_team
> >
> > advertisement version: 2
> > VTP Management Domain: 'cisco'
> > Duplex: full
> >
> >
> > Regards
> > Subodh
> >
> >
> >
> > The information contained in this electronic message
and
> any attachments
> > to
> > this message are intended for the exclusive use of
the
> addressee(s) and
> > may
> > contain proprietary, confidential or privileged
> information. If you are
> > not
> > the intended recipient, you should not disseminate,
> distribute or copy
> > this
> > e-mail. Please notify the sender immediately and
destroy
> all copies of
> > this
> > message and any attachments.
> >
> > WARNING: Computer viruses can be transmitted via
email. The
> recipient
> > should
> > check this email and any attachments for the
presence of
> viruses. The
> > company
> > accepts no liability for any damage caused by any
virus
> transmitted by
> > this
> > email.
> >
> > www.wipro.com <http://www.wipro.com/>
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sat Aug 18 2007 - 08:17:42 ART