From: shiran guez (shiranp3@gmail.com)
Date: Fri Nov 02 2007 - 03:11:53 ART
what dose it mean destination
address = 2000::192.168.1.1 how can you ping 2000::192.168.1.1
R4#ping 2000::10.1.45.5
% Unrecognized host or address, or protocol not running.
interface Ethernet0/1
no ip address
half-duplex
ipv6 address 2001:CC1E:146:146::4/64
ipv6 nat
ipv6 rip RIPng enable
ipv6 rip RIPng default-information originate
!
!
interface Serial1/1
ip address 10.1.45.4 255.255.255.0
ipv6 nat
!
!
ipv6 nat v4v6 source 10.1.45.5 2001:CC1E:5::5
ipv6 nat v6v4 source route-map PT-SOURCE pool v4pool
ipv6 nat v6v4 pool v4pool 10.1.45.10 10.1.45.50 prefix-length 24
ipv6 nat prefix 2000::/96 v4-mapped v4map_acl
!
!
ipv6 prefix-list PT-LIST seq 5 permit 2001:CC1E:146:146::/64
ipv6 prefix-list PT-LIST seq 10 permit 2001:150:1:6::/64
route-map PT-SOURCE permit 10
match ipv6 address prefix-list PT-LIST
!
R4 is connected via Serial to R5, R5 is pure v4 and R4 is the NAT-PT
behind R4 there are R1 and R6 over a Ethernet R6 is Pure v6 and R1 is dual
mode but with no NAT-PT or any other connection between the protocols.
I want to be able to Ping from R6 to the v4 domain and from the v4 Domain to
ping to v6 Domain Dynamically.
In my configuration I went according to the Documentation and I do not
understand practically how the Dynamic works.
On 11/2/07, Phillip.McCollum@ins.com <Phillip.McCollum@ins.com> wrote:
>
> Shiran,
>
> I was pretty confused when working with this as well. Read over this
> line and see if it helps to sink in. Taken from
> http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/
> ipv6_c/sa_natpt.htm#wp1079515:
>
> ==========
> Enabling Traffic to be Sent from an IPv6 Network to an IPv4 Network
> without Using IPv6 Dastination Address Mapping: Example
>
> In the following example, the access list permits any IPv6 source
> address with the prefix 2001::/96 to go to the destination with a
> 2000::/96 prefix. The destination is then translated to the last 32 bit
> of its IPv6 address; for example: source address = 2001::1, destination
> address = 2000::192.168.1.1. The destination then becomes 192.168.1.1 in
> the IPv4 network:
>
> ipv6 nat prefix 2000::/96 v4-mapped v4map_acl
>
> ipv6 access-list v4map_acl
> permit ipv6 2001::/96 2000::/96
>
> ==========
>
> Phillip
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> shiran guez
> Sent: Thursday, November 01, 2007 1:00 PM
> To: Cisco certification
> Subject: IPV6 NAT-PT
>
> I am going out of my mind to figure out this, it seam like this
> technology
> do not want to go trough my head.
> I already went trough the RFC and the Cisco DOC from univercd, but it is
> not
> sinking in.
>
>
> I understand how the Static 1 to 1 work, but the Dynamic I do not see
> how
> can you set a range of address on one protocol and on the other protocol
> without linking them one to one
>
> for say I have IPv6 Network on one side and IPV4 on the other side and
> NAT-PT between them, if i set a pool of IPv4 and a Prefix of /96 for the
> IPv6 what address should I ping from the IPv6 to the IPv4 to reach a
> specific node if it is not mapped how can he know where to go?
>
> if some one have a better explanation and a working sample config I
> would
> much appreciate it as I am pooling hare as we speak.
>
>
> --
> Shiran Guez
> MCSE CCNP NCE1
> http://cciep3.blogspot.com
> http://www.linkedin.com/in/cciep3
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
-- Shiran Guez MCSE CCNP NCE1 http://cciep3.blogspot.com http://www.linkedin.com/in/cciep3
This archive was generated by hypermail 2.1.4 : Sat Dec 01 2007 - 06:37:27 ART