From: Reza Toghraee (reza@toghraee.com)
Date: Sat Oct 18 2008 - 13:50:11 ART
Thanks, but I don't have this command "isdn protocol-emulate network"
FR-BB1(config-if)#do show run int bri 0
Building configuration...
Current configuration : 37 bytes
!
interface BRI0
no ip address
end
FR-BB1(config)#isdn ?
gateway-max-interworking set if gateway has to be transparent.
leased-line Sets a BRI interface to support leased lines on
B &
D channels
silent-boot Ignore ISDN lines while booting
switch-type Select the ISDN switch type
tei-negotiation Set when ISDN TEI negotiation should occur
(global)
voice-call-failure Specify what cause code to emit when a voice
call
fails with no specific cause code
FR-BB1(config)#interface brI 0
FR-BB1(config-if)#isdn ?
T306 Specify Timer T306 in milliseconds
T310 Specify Timer T310 in milliseconds
all-incoming-calls-v120 Answer all incoming calls as V.120
answer1 Specify Called Party number and subaddress
answer2 Specify Called Party number and subaddress
autodetect Enable the automatic spid detection
caller Specify incoming telephone number to be verified
calling-number Specify Calling Number included for outgoing
calls
conference-code Specify a Conference Code
disconnect-cause Specify cause code to return in call rejection to
the switch
fast-rollover-delay Delay between fastrollover dials
guard-timer timer to complete the call.
ie Informational Elements
incoming Process incoming calls
incoming-voice Specify options for incoming calls.
map Specify E.164 address to numbering plan/type
mapping
nfas-order specify nfas DSL search order
not-end-to-end Specify speed when calls received are not isdn
end
to end
outgoing Options for outgoing IEs and messages
outgoing-voice Specify information transfer capability for voice
calls
overlap-receiving Specify if the interface will do Overlap
Receiving
piafs_enabled enable PIAFS (Personal Handy Phone System)
reject Reject incoming calls
send-alerting Specify if Alerting message to be sent out before
Connect message
sending-complete Specify if Sending Complete included in outgoing
SETUP message
snmp SNMP subcommands
spid1 Specify Service Profile IDentifier
spid2 Specify Service Profile IDentifier
static-tei Specify a Static TEI for ISDN BRI
switch-type Select the Interface ISDN switch type
tei-negotiation Set when ISDN TEI negotiation should occur
timeout-signaling Flush D channel if a signaling packet can't be
transmitted in 1 second
timer Specify ISDN Timer values to be changed
transfer-code Specify a Transfer Code (Default 61)
transition-delay Delay before bringing D channel up
transparent Pass Cause Values transparently
twait-disable Delay National ISDN BRI switchtype from
activating
interface on powerup
v110 Specify V.110 over ISDN
voice-priority Specify Voice Priority
x25 Configure x25 over the D channel
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of Nick
Matthews
Sent: Saturday, October 18, 2008 8:41 PM
To: Scott M Vermillion
Cc: Radioactive Frog; Reza Toghraee; Cisco certification
Subject: Re: OT: is it possible to have BRI back2back connection?
Yes, you can do both PRI and BRI back-to-back. T1 Crossover with
emulate-network on one side.
Nick
On Sat, Oct 18, 2008 at 12:20 PM, Scott M Vermillion <
scott_ccie_list@it-ag.com> wrote:
> Hey Frog,
>
> I didn't see your reply before posting about the need for an ISDN
> simulator.
> This work for BRIs too? Way cool if so...
>
> Scott
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Radioactive Frog
> Sent: Saturday, October 18, 2008 6:37 AM
> To: Reza Toghraee
> Cc: Cisco certification
> Subject: Re: OT: is it possible to have BRI back2back connection?
>
> yes u can do that, real easy one :)
>
> r1---isdn pri------------r2
>
> just use a isdn crossover cable. remember its not E1 crsoss over, neither
> ethernet crossover.
>
>
> router1 =>isdn protocol-emulate network
> router2 =>isdn protocol-emulate user
>
> confirm it using show isdn status.
>
> thats all.
>
> -frog
>
>
> On Sat, Oct 18, 2008 at 8:40 PM, Reza Toghraee <reza@toghraee.com> wrote:
>
> > Hi
> >
> >
> >
> > Is there any way to connect 2 cisco 25xx routers with their BRI
interface
> > without any isdn switch?
> >
> >
> >
> > Thanks
> >
> > Reza
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sat Nov 01 2008 - 15:35:21 ARST