Re: pls help, easy ospf question

yea. i havent gotten to the frame relay sections. i just figured i would
start on ospf lab 1.

On Fri, May 1, 2009 at 3:55 PM, Ryan West <rwest_at_zyedge.com> wrote:

> You're using Narbik's Soup to Nuts, right? Did you start on the
> Frame-Relay section? I think it would be a bad idea to start on the most
> complicated IGP for the R&S as your first IGP before verifying your
> Frame-Relay sections.
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> belletjetrekken
> Sent: Friday, May 01, 2009 4:46 PM
> To: Bryan Bartik
> Cc: Baik, Chan; Cisco certification
> Subject: Re: pls help, easy ospf question
>
> frame relay
>
> R1 can't ping R2 and R3 can't ping R4.
>
> R1#sh ip ospf nei
>
> R1#
>
> R2#sh ip ospf nei
>
> Neighbor ID Pri State Dead Time Address Interface
> 3.3.3.3 1 FULL/BDR 00:00:32 131.1.23.3
> FastEthernet0/0
> R2#
> R3#sh ip ospf nei
>
> Neighbor ID Pri State Dead Time Address Interface
> 2.2.2.2 1 FULL/DR 00:00:34 131.1.23.2
> FastEthernet0/0
> R3#
> R4#sh ip ospf nei
>
> R4#
>
>
>
>
>
> R1#siib
> Interface IP-Address OK? Method Status
> Protocol
> FastEthernet0/0 unassigned YES NVRAM up
> up
> Serial0/0 unassigned YES manual down
> down
> Serial0/0.12 131.1.12.1 YES manual down
> down
> FastEthernet0/1 unassigned YES NVRAM administratively down
> down
> Serial0/1 unassigned YES unset administratively down
> down
> Loopback0 1.1.1.1 YES manual up
> up
> R1#
> R2#siib
> Interface IP-Address OK? Method Status
> Protocol
> FastEthernet0/0 131.1.23.2 YES manual up
> up
> Serial0/0 unassigned YES manual down
> down
> Serial0/0.21 131.1.12.2 YES manual down
> down
> FastEthernet0/1 unassigned YES unset administratively down
> down
> Serial0/1 unassigned YES unset administratively down
> down
> Loopback0 2.2.2.2 YES manual up
> up
> R2#
> R3#siib
> Interface IP-Address OK? Method Status
> Protocol
> FastEthernet0/0 131.1.23.3 YES manual up
> up
> Serial0/0 unassigned YES manual down
> down
> Serial0/0.34 131.1.34.3 YES manual down
> down
> FastEthernet0/1 unassigned YES unset administratively down
> down
> Serial0/1 unassigned YES unset administratively down
> down
> Loopback0 3.3.3.3 YES manual up
> up
> R3#
> R4#siib
> Interface IP-Address OK? Method Status
> Protocol
> FastEthernet0/0 unassigned YES unset administratively down
> down
> Serial0/0 unassigned YES manual down
> down
> Serial0/0.43 131.1.34.3 YES manual down
> down
> FastEthernet0/1 unassigned YES unset administratively down
> down
> Loopback0 4.4.4.4 YES manual up
> up
> R4#
>
>
> On Fri, May 1, 2009 at 3:07 PM, Bryan Bartik <bbartik_at_ipexpert.com> wrote:
>
> > I thought you said you could not ping between R1 and R2. Is the interface
> > up/up between them? Are you using PPP or Frame-relay?
> >
> >
> > On Fri, May 1, 2009 at 2:01 PM, belletjetrekken <
> belletjetrekken_at_gmail.com
> > > wrote:
> >
> >> what do i do now ?
> >>
> >> R1(config-subif)#frame-relay map ip 131.1.12.2 16
> >> Only frame-relay interface-dlci command should beused on point-to-point
> >> interfaces not frame-relay map
> >>
> >> On Fri, May 1, 2009 at 10:41 AM, Baik, Chan <Chan.Baik_at_viacom.com>
> wrote:
> >>
> >> > You need to configure something like this:
> >> >
> >> > interface serial s0/0
> >> > encap frame-relay
> >> >
> >> > interface serial s0/0.12
> >> > frame-relay map ip <ip addr of other side> <dlci>
> >> >
> >> > ------------------------------
> >> > *From:* belletjetrekken [mailto:belletjetrekken_at_gmail.com]
> >> > *Sent:* Friday, May 01, 2009 8:38 AM
> >> > *To:* Baik, Chan
> >> >
> >> > *Subject:* Re: pls help, easy ospf question
> >> >
> >> > frame-relay
> >> >
> >> > On Fri, May 1, 2009 at 10:31 AM, Baik, Chan <Chan.Baik_at_viacom.com>
> >> wrote:
> >> >
> >> >> Are you supposed to use frame-relay encapsulation on serial 0/0 or
> >> hdlc?
> >> >>
> >> >> ------------------------------
> >> >> *From:* belletjetrekken [mailto:belletjetrekken_at_gmail.com]
> >> >> *Sent:* Friday, May 01, 2009 8:28 AM
> >> >> *To:* Ryan West
> >> >> *Cc:* Abraham, Tharak; Baik, Chan; Cisco certification
> >> >>
> >> >> *Subject:* Re: pls help, easy ospf question
> >> >>
> >> >> here is some more layout info attached
> >> >>
> >> >> On Fri, May 1, 2009 at 10:23 AM, Ryan West <rwest_at_zyedge.com> wrote:
> >> >>
> >> >>> Can you ping 12.1, I don t see any hello s in that direction.
> Also,
> >> >>> can turn off the other debugs once you can ping and deb ip os adj
> ?
> >> >>>
> >> >>>
> >> >>>
> >> >>> -ryan
> >> >>>
> >> >>>
> >> >>>
> >> >>> *From:* belletjetrekken [mailto:belletjetrekken_at_gmail.com]
> >> >>> *Sent:* Friday, May 01, 2009 11:14 AM
> >> >>> *To:* Abraham, Tharak
> >> >>> *Cc:* Ryan West; Baik, Chan; Cisco certification
> >> >>>
> >> >>> *Subject:* Re: pls help, easy ospf question
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>> On Fri, May 1, 2009 at 10:08 AM, Abraham, Tharak <
> >> >>> tharakabraham_at_gmail.com> wrote:
> >> >>>
> >> >>> Were the adjacencies formed before turning on authentication?
> >> >>>
> >> >>> Could you disable the authentication and give a shot?
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>> On Fri, May 1, 2009 at 5:03 PM, Ryan West <rwest_at_zyedge.com> wrote:
> >> >>>
> >> >>> Post debugs.
> >> >>>
> >> >>>
> >> >>> -----Original Message-----
> >> >>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
> Behalf
> >> Of
> >> >>> belletjetrekken
> >> >>> Sent: Friday, May 01, 2009 10:57 AM
> >> >>> To: Baik, Chan
> >> >>> Cc: Cisco certification
> >> >>> Subject: Re: pls help, easy ospf question
> >> >>>
> >> >>> i just turned enabled the serial interfaces..but still the routes
> are
> >> not
> >> >>> showing up
> >> >>>
> >> >>> On Fri, May 1, 2009 at 9:49 AM, Baik, Chan <Chan.Baik_at_viacom.com>
> >> wrote:
> >> >>>
> >> >>> > It looks like your serial interfaces are shut down.
> >> >>> >
> >> >>> > -----Original Message-----
> >> >>> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
> >> Behalf
> >> >>> Of
> >> >>> > junk mail
> >> >>> > Sent: Friday, May 01, 2009 7:24 AM
> >> >>> > To: Cisco certification
> >> >>> > Subject: pls help, easy ospf question
> >> >>> >
> >> >>> > studying for my r & s, i configured 4 routers for ospf and for
> some
> >> >>> > reason R1's ospf routes are not showing up in the routing table,
> can
> >> >>> > somebody help me figure out why the routes are not showing up ? i
> >> >>> > attached sh run's here..
> >> >>> >
> >> >>> > thanks
> >> >>> >
> >> >>> > belletjetrekken
> >> >>> > R1#sh run
> >> >>> > Building configuration...
> >> >>> >
> >> >>> > Current configuration : 1838 bytes
> >> >>> > !
> >> >>> > version 12.4
> >> >>> > service timestamps debug datetime msec
> >> >>> > service timestamps log datetime msec
> >> >>> > no service password-encryption
> >> >>> > !
> >> >>> > hostname R1
> >> >>> > !
> >> >>> > boot-start-marker
> >> >>> > boot-end-marker
> >> >>> > !
> >> >>> > !
> >> >>> > no aaa new-model
> >> >>> > !
> >> >>> > resource policy
> >> >>> > !
> >> >>> > no network-clock-participate slot 1
> >> >>> > no network-clock-participate wic 0
> >> >>> > ip subnet-zero
> >> >>> > ip cef
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > no ip domain lookup
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > interface Loopback0
> >> >>> > ip address 1.1.1.1 255.0.0.0
> >> >>> > !
> >> >>> > interface FastEthernet0/0
> >> >>> > no ip address
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/0
> >> >>> > no ip address
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > interface Serial0/0.12
> >> >>> > ip address 131.1.12.1 255.255.255.0
> >> >>> > ip ospf message-digest-key 1 md5 Cisco12 !
> >> >>> > interface FastEthernet0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > router ospf 1
> >> >>> > router-id 1.1.1.1
> >> >>> > log-adjacency-changes
> >> >>> > area 2 authentication message-digest
> >> >>> > network 0.0.0.0 255.255.255.255 area 2
> >> >>> > !
> >> >>> > ip classless
> >> >>> > !
> >> >>> > !
> >> >>> > no ip http server
> >> >>> > no ip http secure-server
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > control-plane
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > alias exec siib show ip int br
> >> >>> > alias exec scn show cdp neighbors
> >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show vlan
> >> >>> brief
> >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> alias
> >> >>> exec
> >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf database
> >> >>> router
> >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> alias
> >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> alias
> >> >>> exec
> >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> >> detail
> >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> >> spanning-tree
> >> >>> > root alias exec ssb show spanning-tree blockedports alias exec sv
> >> show
> >> >>> > version alias exec sir show ip route !
> >> >>> > line con 0
> >> >>> > exec-timeout 0 0
> >> >>> > logging synchronous
> >> >>> > line aux 0
> >> >>> > line vty 0 4
> >> >>> > login
> >> >>> > !
> >> >>> > !
> >> >>> > end
> >> >>> >
> >> >>> > R1#
> >> >>> > R2#sh run
> >> >>> > Building configuration...
> >> >>> >
> >> >>> > Current configuration : 1974 bytes
> >> >>> > !
> >> >>> > version 12.4
> >> >>> > service timestamps debug datetime msec
> >> >>> > service timestamps log datetime msec
> >> >>> > no service password-encryption
> >> >>> > !
> >> >>> > hostname R2
> >> >>> > !
> >> >>> > boot-start-marker
> >> >>> > boot-end-marker
> >> >>> > !
> >> >>> > !
> >> >>> > no aaa new-model
> >> >>> > !
> >> >>> > resource policy
> >> >>> > !
> >> >>> > no network-clock-participate slot 1
> >> >>> > no network-clock-participate wic 0
> >> >>> > ip subnet-zero
> >> >>> > ip cef
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > no ip domain lookup
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > interface Loopback0
> >> >>> > ip address 2.2.2.2 255.0.0.0
> >> >>> > !
> >> >>> > interface FastEthernet0/0
> >> >>> > ip address 131.1.23.2 255.255.255.0
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/0
> >> >>> > no ip address
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > interface Serial0/0.21
> >> >>> > ip address 131.1.12.2 255.255.255.0
> >> >>> > ip ospf message-digest-key 1 md5 Cisco12 !
> >> >>> > interface FastEthernet0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > router ospf 1
> >> >>> > router-id 2.2.2.2
> >> >>> > log-adjacency-changes
> >> >>> > area 1 virtual-link 3.3.3.3
> >> >>> > area 2 authentication message-digest
> >> >>> > network 2.2.2.2 0.0.0.0 area 2
> >> >>> > network 22.2.2.2 0.0.0.0 area 1
> >> >>> > network 131.1.12.2 0.0.0.0 area 2
> >> >>> > network 131.1.23.2 0.0.0.0 area 1
> >> >>> > !
> >> >>> > ip classless
> >> >>> > !
> >> >>> > !
> >> >>> > ip http server
> >> >>> > no ip http secure-server
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > control-plane
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > alias exec siib show ip int br
> >> >>> > alias exec scn show cdp neighbors
> >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show vlan
> >> >>> brief
> >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> alias
> >> >>> exec
> >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf database
> >> >>> router
> >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> alias
> >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> alias
> >> >>> exec
> >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> >> detail
> >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> >> spanning-tree
> >> >>> > root alias exec ssb show spanning-tree blockedports alias exec sv
> >> show
> >> >>> > version alias exec sir show ip route !
> >> >>> > line con 0
> >> >>> > exec-timeout 0 0
> >> >>> > logging synchronous
> >> >>> > line aux 0
> >> >>> > line vty 0 4
> >> >>> > !
> >> >>> > !
> >> >>> > end
> >> >>> >
> >> >>> > R2#
> >> >>> > R3#sh run
> >> >>> > Building configuration...
> >> >>> >
> >> >>> > Current configuration : 1897 bytes
> >> >>> > !
> >> >>> > version 12.4
> >> >>> > service timestamps debug datetime msec
> >> >>> > service timestamps log datetime msec
> >> >>> > no service password-encryption
> >> >>> > !
> >> >>> > hostname R3
> >> >>> > !
> >> >>> > boot-start-marker
> >> >>> > boot-end-marker
> >> >>> > !
> >> >>> > !
> >> >>> > no aaa new-model
> >> >>> > !
> >> >>> > resource policy
> >> >>> > !
> >> >>> > no network-clock-participate slot 1
> >> >>> > no network-clock-participate wic 0
> >> >>> > ip subnet-zero
> >> >>> > ip cef
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > no ip domain lookup
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > interface Loopback0
> >> >>> > ip address 3.3.3.3 255.0.0.0
> >> >>> > !
> >> >>> > interface FastEthernet0/0
> >> >>> > ip address 131.1.23.3 255.255.255.0
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/0
> >> >>> > no ip address
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > interface Serial0/0.34
> >> >>> > ip address 131.1.34.3 255.255.255.0
> >> >>> > !
> >> >>> > interface FastEthernet0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > router ospf 1
> >> >>> > router-id 3.3.3.3
> >> >>> > log-adjacency-changes
> >> >>> > area 1 virtual-link 2.2.2.2
> >> >>> > network 3.3.3.3 0.0.0.0 area 1
> >> >>> > network 33.3.3.3 0.0.0.0 area 0
> >> >>> > network 131.1.23.3 0.0.0.0 area 1
> >> >>> > network 131.1.34.3 0.0.0.0 area 0
> >> >>> > !
> >> >>> > ip classless
> >> >>> > !
> >> >>> > !
> >> >>> > no ip http server
> >> >>> > no ip http secure-server
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > control-plane
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > alias exec siib show ip int br
> >> >>> > alias exec scn show cdp neighbors
> >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show vlan
> >> >>> brief
> >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> alias
> >> >>> exec
> >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf database
> >> >>> router
> >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> alias
> >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> alias
> >> >>> exec
> >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> >> detail
> >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> >> spanning-tree
> >> >>> > root alias exec ssb show spanning-tree blockedports alias exec sv
> >> show
> >> >>> > version alias exec sir show ip route !
> >> >>> > line con 0
> >> >>> > exec-timeout 0 0
> >> >>> > logging synchronous
> >> >>> > line aux 0
> >> >>> > line vty 0 4
> >> >>> > !
> >> >>> > !
> >> >>> > end
> >> >>> >
> >> >>> > R3#
> >> >>> > R4#sh run
> >> >>> > Building configuration...
> >> >>> >
> >> >>> > Current configuration : 1683 bytes
> >> >>> > !
> >> >>> > version 12.4
> >> >>> > service timestamps debug datetime msec
> >> >>> > service timestamps log datetime msec
> >> >>> > no service password-encryption
> >> >>> > !
> >> >>> > hostname R4
> >> >>> > !
> >> >>> > boot-start-marker
> >> >>> > boot-end-marker
> >> >>> > !
> >> >>> > !
> >> >>> > no aaa new-model
> >> >>> > !
> >> >>> > resource policy
> >> >>> > !
> >> >>> > no network-clock-participate slot 1
> >> >>> > no network-clock-participate wic 0
> >> >>> > ip subnet-zero
> >> >>> > ip cef
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > no ip domain lookup
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > interface Loopback0
> >> >>> > ip address 4.4.4.4 255.0.0.0
> >> >>> > !
> >> >>> > interface FastEthernet0/0
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > interface Serial0/0
> >> >>> > no ip address
> >> >>> > no dce-terminal-timing-enable
> >> >>> > !
> >> >>> > interface Serial0/0.43
> >> >>> > ip address 131.1.34.3 255.255.255.0
> >> >>> > !
> >> >>> > interface FastEthernet0/1
> >> >>> > no ip address
> >> >>> > shutdown
> >> >>> > duplex auto
> >> >>> > speed auto
> >> >>> > !
> >> >>> > router ospf 1
> >> >>> > router-id 4.4.4.4
> >> >>> > log-adjacency-changes
> >> >>> > network 0.0.0.0 255.255.255.255 area 0
> >> >>> > !
> >> >>> > ip classless
> >> >>> > !
> >> >>> > !
> >> >>> > no ip http server
> >> >>> > no ip http secure-server
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > control-plane
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > !
> >> >>> > alias exec siib show ip int br
> >> >>> > alias exec scn show cdp neighbors
> >> >>> > alias exec scnd show cdp neighbors detail alias exec svb show vlan
> >> >>> brief
> >> >>> > alias exec svs show vtp stat alias exec sion show ip ospf nei
> alias
> >> >>> exec
> >> >>> > siond show ip ospf nei det alias exec siodr show ip ospf database
> >> >>> router
> >> >>> > alias exec sioi show ip ospf int alias exec sen show eigrp nei
> alias
> >> >>> > exec send show eigrp nei det alias exec ss show spanning-tree
> alias
> >> >>> exec
> >> >>> > sss show spanning-tree summary alias exec ssd show spanning-tree
> >> detail
> >> >>> > alias exec ssm show spanning-tree mst alias exec ssr show
> >> spanning-tree
> >> >>> > root alias exec ssb show spanning-tree blockedports alias exec sv
> >> show
> >> >>> > version alias exec sir show ip route !
> >> >>> > line con 0
> >> >>> > exec-timeout 0 0
> >> >>> > logging synchronous
> >> >>> > line aux 0
> >> >>> > line vty 0 4
> >> >>> > !
> >> >>> > !
> >> >>> > end
> >> >>> >
> >> >>> > R4#
> >> >>> >
> >> >>> >
> >> >>> > Blogs and organic groups at http://www.ccie.net
> >> >>> >
> >> >>> >
> >> _______________________________________________________________________
> >> >>> > Subscription information may be found at:
> >> >>> > http://www.groupstudy.com/list/CCIELab.html
> >> >>>
> >> >>>
> >> >>> Blogs and organic groups at http://www.ccie.net
> >> >>>
> >> >>>
> >> _______________________________________________________________________
> >> >>> Subscription information may be found at:
> >> >>> http://www.groupstudy.com/list/CCIELab.html
> >> >>>
> >> >>>
> >> >>> Blogs and organic groups at http://www.ccie.net
> >> >>>
> >> >>>
> >> _______________________________________________________________________
> >> >>> Subscription information may be found at:
> >> >>> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >
> >
> > --
> > Bryan Bartik
> > CCIE #23707, CCNP
> > Sr. Support Engineer - IPexpert, Inc.
> > URL: http://www.IPexpert.com
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri May 01 2009 - 16:12:02 ART