Re: AToM FR-Ethernet Interworking problem

Hi Rin,

Looks like you are doing bridged mode so I believe you will need
"frame-relay map bridge" on the CE (R4). Also, I have this working without
specifying a switched DLCI on the PE (R1). What reference are you using?

On Thu, May 28, 2009 at 9:46 AM, Rin <rintrum@
gmail.com> wrote:

> Hi all,
>
>
>
> I have topo as below:
>
>
> R4(s1/0)------FR---------(s2/0)R1(s2/1)----------(s1/2)R3(s1/3)-------------
> -s2/1)R2(f0/0)-----------------(e0/0)R6
>
> MPLS is running on R1,R2,R3. I want to create a pseudowire b/w R1 & R4.
> Here's my configuration:
>
> On R1:
>
> pseudowire-class vl-fr-iwe
>
> encapsulation mpls
>
> interworking ethernet
>
> !
>
> interface Serial2/0
>
> encapsulation frame-relay
>
> serial restart-delay 0
>
> frame-relay interface-dlci 104 switched
>
> !
>
> connect r1r2 Serial2/0 104 l2transport
>
> xconnect 2.2.2.2 406 pw-class vl-fr-iwe
>
>
>
> On R2:
>
> pseudowire-class vl-fr-iwe
>
> encapsulation mpls
>
> interworking ethernet
>
> !
>
> interface FastEthernet0/0
>
> no ip address
>
> no cdp enable
>
> no clns route-cache
>
> xconnect 1.1.1.1 406 pw-class vl-fr-iwe
>
>
>
> On R4:
>
> interface Serial1/0
>
> ip address 172.10.46.4 255.255.255.0
>
> encapsulation frame-relay
>
> serial restart-delay 0
>
> frame-relay map ip 172.10.46.6 401 broadcast
>
>
>
> On R6:
>
> interface Ethernet0/0
>
> ip address 172.10.46.6 255.255.255.0
>
>
>
> Below is my verification:
>
> Rack1R1#sho mpls l2 vc de
>
> Local interface: Se2/0 up, line protocol up, FR DLCI 104 up
>
> MPLS VC type is Ethernet, interworking type is Ethernet
>
> Destination address: 2.2.2.2, VC ID: 406, VC status: up
>
> Output interface: Se2/1, imposed label stack {19 17}
>
> Preferred path: not configured
>
> Default path: active
>
> Tunnel label: 17, next hop point2point
>
> Create time: 00:13:57, last status change time: 00:13:27
>
> Signaling protocol: LDP, peer 2.2.2.2:0 up
>
> MPLS VC labels: local 16, remote 19
>
> Group ID: local 0, remote 0
>
> MTU: local 1500, remote 1500
>
> Remote interface description:
>
> Sequencing: receive disabled, send disabled
>
> VC statistics:
>
> packet totals: receive 431, send 0
>
> byte totals: receive 30464, send 0
>
> packet drops: receive 0, send 0
>
>
>
> Rack1R2#sho mpls l2 vc de
>
> Local interface: Fa0/0 up, line protocol up, Ethernet up
>
> Destination address: 1.1.1.1, VC ID: 406, VC status: up
>
> Output interface: Se2/1, imposed label stack {16 16}
>
> Preferred path: not configured
>
> Default path: active
>
> Tunnel label: 16, next hop point2point
>
> Create time: 00:15:09, last status change time: 00:13:47
>
> Signaling protocol: LDP, peer 1.1.1.1:0 up
>
> MPLS VC labels: local 19, remote 16
>
> Group ID: local 0, remote 0
>
> MTU: local 1500, remote 1500
>
> Remote interface description:
>
> Sequencing: receive disabled, send disabled
>
> VC statistics:
>
> packet totals: receive 0, send 441
>
> byte totals: receive 0, send 37864
>
> packet drops: receive 0, send 0
>
>
>
> Rack1R4#sho fram map
>
> Serial1/0 (up): ip 172.10.46.6 dlci 401(0x191,0x6410), static,
>
> broadcast,
>
> CISCO, status defined, active
>
>
>
> So everything seems ok, the link between R2-R6 is ok too. However I cannot
> ping from R4 to R6.
>
> Rack1R4#ping 172.10.46.6
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 172.10.46.6, timeout is 2 seconds:
>
> .....
>
> Success rate is 0 percent (0/5)
>
>
>
> Can anyone help? Sorry for the long email. Thank you.
>
> Rin
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>

-- 
Bryan Bartik
CCIE #23707 (R&S), CCNP
Sr. Support Engineer - IPexpert, Inc.
URL: http://www.IPexpert.com
Blogs and organic groups at http://www.ccie.net