Re: leased line with G703 module using router 2851 and 2801

google on "frame-relay hub and spoke" or "frame-relay point to multipoint"
http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=6

R4(config)#interface s1/2.403 point-to-point
R4(config-subif)#frame-relay interface-dlci ?
 <16-1007> Define a switched or locally terminated DLCI

R4(config-subif)#frame-relay interface-dlci 403 ?
 cisco Use CISCO Encapsulation
 ietf Use RFC1490/RFC2427 Encapsulation
 ppp Use RFC1973 Encapsulation to support PPP over FR
 protocol Optional protocol information for remote end
<cr>
R4#show frame-relay map
Serial1/2.403 (up): point-to-point dlci, dlci 403(0xC9,0x3090), broadcast
     status defined, active

R4#

On Thu, Jul 16, 2009 at 8:54 PM, erwin wijaya <erwinem.wijaya_at_gmail.com>wrote:

> that's great!....
> would u like to show me how to config my router coz i need time to learn it
> before, coz in near time we'll doing that.
>
> thanks again
> regards -ew
> ----
> Radioactive Frog wrote:
>
>> yes that is possible. Your lease line provider should map your individual
>> 2 megs timeslots to all remote site using a MUX.
>> In central site u can just use one interface with frame-relay
>> point-to-multipoint subinterface.
>>
>>
>> On Wed, Jul 15, 2009 at 8:02 PM, Mohammed Naviwala <monavy_at_gmail.com<mailto:
>> monavy_at_gmail.com>> wrote:
>>
>> well if that is the requirement, you were better off with the
>> MPLS........leased lines dont work that way....
>>
>>
>> On Wed, Jul 15, 2009 at 1:37 PM, erwin wijaya
>> <erwinem.wijaya_at_gmail.com <mailto:erwinem.wijaya_at_gmail.com>> wrote:
>>
>> Hi again,
>>
>> Is it possible at central site only using 1 router and 1 vwic
>> G703? coz, all branch office connected leased line to central
>> site. so we just adding 1 card G703 per branch?
>>
>> thanks again..
>> regards-Erwin
>>
>>
>>
>> Radioactive Frog wrote:
>>
>> u only need 1 routerat the central site wiht 3 serial or
>> E1 interface
>> (depends where E1 line terminates). If its close to
>> (within 120
>> meters) PDH/SDH MuX use E1 else u may need to use a e1
>> extender
>> convertor.
>>
>>
>> On 7/7/09, erwinem wijaya <erwinem.wijaya_at_gmail.com
>> <mailto:erwinem.wijaya_at_gmail.com>> wrote:
>>
>> Hi all,
>> another questions, for example i need to connecting
>> office B to A, also
>> ofice C to A, and office D to A. office A is a central
>> office. do wee need 3
>> router at office A or we just need 1 router at office
>> A if we'll using
>> leased line. Today we using 1 router for 3 branch
>> office with MPLS.
>>
>> thanks for any helps.
>>
>> ----- Original Message -----
>> From: Radioactive Frog
>> To: erwin wijaya
>> Cc: ccielab_at_groupstudy.com
>> <mailto:ccielab_at_groupstudy.com>
>> Sent: Tuesday, June 30, 2009 8:39 PM
>> Subject: Re: leased line with G703 module using
>> router 2851 and 2801
>>
>>
>> Hi Erwin,It's damn easy!controller E1 2/0channel-group
>> 0 unframedafter
>> issuing above command the router creates a logical
>> serial interface where
>> you can put your WAN ip, just like you've seen serial
>> port.assign ip here
>> for wan side of thigns.
>> interface Serial2/0:0ip address 1.1.1.1
>> 255.255.255.0verify by using 'show
>> controller e1 1/0 and show inter serial2/0:0"HTH-frog
>>
>> On Tue, Jun 30, 2009 at 5:33 PM, erwin wijaya
>> <erwinem.wijaya_at_gmail.com
>> <mailto:erwinem.wijaya_at_gmail.com>>
>> wrote:
>>
>> dear all,
>> how to configure my router when i need to
>> connecting my office (router
>> 2851) with branch office (router 2801) using G703
>> module. We are using
>> leased line conection to connecting both office. Also
>> we'll use to send data
>> and voice..present we using MPLS tech to connecting
>> both office. Is it the
>> same way?
>>
>> thanks alot for any helps.
>> regards - erwin
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> -- Best Regards
>>
>> Mohammed Abdul Razzaq
>>
>>
>> If you are not small enough to loose, you are not big enough to win..

Blogs and organic groups at http://www.ccie.net
Received on Thu Jul 16 2009 - 23:41:47 ART