Re: OSPF problem..pls help.

Sorry , mean dynamic not dynamips :)

----- Original Message -----
From: "Mohamed El Henawy" <m.henawy_at_link.net>
To: "Mohamed El Henawy" <m.henawy_at_link.net>; "Naufal Jamal"
<naufalccie_at_yahoo.in>; <ccielab_at_groupstudy.com>
Sent: Sunday, September 13, 2009 1:21 PM
Subject: Re: OSPF problem..pls help.

>i think problem in dynamips FR maping...
>
>
> Sep 13 11:20:38.243: OSPF: Rcv pkt from 1.1.24.2, Serial0/0/0, area
> =====>
> Serial0/0/0
>> 0.0.0.
>>
>> interface Serial0/1/0 ===========>
>> ip address 1.1.24.4 255.255.255.0
>> encapsulation frame-relay
>> ip ospf network point-to-point
>> frame-relay map ip 1.1.24.4 402
>> frame-relay map ip 1.1.24.2 402 broadcast
>> no frame-relay inverse-arp
>
>
> ----- Original Message -----
> From: "Mohamed El Henawy" <m.henawy_at_link.net>
> To: "Naufal Jamal" <naufalccie_at_yahoo.in>; <ccielab_at_groupstudy.com>
> Sent: Sunday, September 13, 2009 1:07 PM
> Subject: Re: OSPF problem..pls help.
>
>
>> Not really quite sure but I think problem in the R-IDs perhaps you
>> changed
>> it after it already selected the interface.try to hard code it..also
>> check
>> the subnet mask
>> try to reload the babies again :)
>>
>> ----- Original Message -----
>> From: "Naufal Jamal" <naufalccie_at_yahoo.in>
>> To: <ccielab_at_groupstudy.com>
>> Sent: Sunday, September 13, 2009 1:16 PM
>> Subject: OSPF problem..pls help.
>>
>>
>>> Hi,
>>>
>>> I have a full-mesh of ospf network but having problems between R4 and R2
>>> point-to-point network type .here is the config/debug on both the
>>> routers.the
>>> neighbourship never comes up.
>>>
>>>
>>> R4
>>>
>>> interface Serial0/1/0
>>> ip address 1.1.24.4 255.255.255.0
>>> encapsulation frame-relay
>>> ip ospf network point-to-point
>>> frame-relay map ip 1.1.24.4 402
>>> frame-relay map ip 1.1.24.2 402 broadcast
>>> no frame-relay inverse-arp
>>> end
>>>
>>> R4
>>>
>>> (config-if)#do debug ip ospf ev
>>> OSPF events debugging is on
>>> R4(config-if)#
>>> *Sep 13 11:20:38.131: OSPF: Send hello to 224.0.0.5 area 2 on
>>> Serial0/1/0
>>> from
>>> 1
>>> .1.24.4
>>> *Sep 13 11:20:38.243: OSPF: Rcv pkt from 1.1.24.2, Serial0/0/0, area
>>> 0.0.0.0
>>> mismatch area 0.0.0.2 in the header
>>>
>>> sh ip ospf ne
>>> Neighbor ID Pri State Dead Time Address
>>> Interface
>>> 1.1.3.3 1 FULL/DROTHER 00:01:51 1.1.100.3
>>> Serial0/0/0
>>> 1.1.6.6 1 FULL/BDR 00:01:47 1.1.100.6
>>> Serial0/0/0
>>>
>>> router ospf 1
>>> log-adjacency-changes
>>> network 1.1.4.4 0.0.0.0 area 0
>>> network 1.1.24.4 0.0.0.0 area 2
>>> network 1.1.100.4 0.0.0.0 area 0
>>> neighbor 1.1.100.3
>>> neighbor 1.1.100.6
>>>
>>> R2
>>>
>>>
>>> R2(config-if)#
>>> *Mar 1 16:50:33.663: OSPF: Send hello to 224.0.0.5 area 2 on
>>> FastEthernet0/0
>>> fr
>>> om 1.1.26.2
>>> *Mar 1 16:50:34.491: OSPF: Rcv hello from 1.1.4.4 area 2 from Serial0/0
>>> 1.1.24.
>>> 4
>>> *Mar 1 16:50:34.491: OSPF: Send immediate hello to nbr 1.1.4.4, src
>>> address
>>> 1.1
>>> .24.4, on Serial0/0
>>> *Mar 1 16:50:34.495: OSPF: Send hello to 224.0.0.5 area 2 on Serial0/0
>>> from
>>> 1.1
>>> .24.2
>>> *Mar 1 16:50:34.495: OSPF: End o
>>> *Mar 1 16:58:55.403: OSPF: Rcv hello from 1.1.6.6 area 2 from
>>> FastEthernet0/0
>>> 1
>>> .1.26.6
>>> *Mar 1 16:58:55.403: OSPF: End of hello processing
>>> R2(config-if)#
>>> R2(config-if)#do
>>> *Mar 1 16:58:58.567: OSPF: Send hello to 224.0.0.5 area 2 on Serial0/0
>>> from
>>> 1.1
>>> .24.2
>>> R2(config-if)#do u all
>>> All possible debugging has been turned off
>>> R2(config-if)#do sh ip ospf ne
>>> Neighbor ID Pri State Dead Time Address
>>> Interface
>>> 1.1.4.4 0 INIT/ - 00:00:32 1.1.24.4
>>> Serial0/0
>>> 1.1.6.6 1 FULL/BDR 00:00:33 1.1.26.6
>>> FastEthernet0/0
>>>
>>> interface Serial0/0
>>> ip address 1.1.24.2 255.255.255.0
>>> encapsulation frame-relay
>>> ip ospf network point-to-point
>>> frame-relay map ip 1.1.24.2 204
>>> frame-relay map ip 1.1.24.4 204 broadcast
>>> no frame-relay inverse-arp
>>> frame-relay lmi-type cisco
>>> end
>>>
>>> router ospf 1
>>> log-adjacency-changes
>>> network 1.1.2.2 0.0.0.0 area 2
>>> network 1.1.24.2 0.0.0.0 area 2
>>> network 1.1.26.2 0.0.0.0 area 2
>>>
>>> neighborship with R3 and R6 is o.k dont understand why it is not comin
>>> up
>>> between R2 and R4 p2p link...
>>>
>>> Thanks,
>>> Naufal
>>>
>>>
>>> See the Web&#39;s breaking stories, chosen by people like you.
>>> Check out Yahoo! Buzz. http://in.buzz.yahoo.com/
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>> --------------------------------------------------------------------------------
>>
>>
>>
>> No virus found in this incoming message.
>> Checked by AVG - www.avg.com
>> Version: 8.5.409 / Virus Database: 270.13.94/2367 - Release Date:
>> 09/13/09
>> 05:50:00
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>
>
> --------------------------------------------------------------------------------
>
>
>
> No virus found in this incoming message.
> Checked by AVG - www.avg.com
> Version: 8.5.409 / Virus Database: 270.13.94/2367 - Release Date: 09/13/09
> 05:50:00
>

--------------------------------------------------------------------------------

No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.409 / Virus Database: 270.13.94/2367 - Release Date: 09/13/09
05:50:00

Blogs and organic groups at http://www.ccie.net
Received on Sun Sep 13 2009 - 13:32:33 ART