Re: MPLS Traffic-Engineering Dynamic Tunnel

I don't have too much experience with TE but normally I haven't seen
under the tunnel definition "tunnel source " explicitly configured.
Could that be a problem and if not when does one define tunnel source
under TE?

-Rich

On Fri, Oct 30, 2009 at 10:01 PM, Bryan Bartik <bbartik_at_ipexpert.com> wrote:
> Something's wrong on R7...there is no TE topology information for it. Is
> that the full output of the command?
>
> On Fri, Oct 30, 2009 at 7:05 PM, <armylegionmedic_at_aol.com> wrote:
>>
>> Hello Bryan,
>> Thanks for your response, here is the info pulled from the config
>> R9
>> mpls traffic-eng tunnels
>> no mpls traffic-eng auto-bw timers frequency 0
>> mpls ldp router-id Loopback0
>> mpls label range 9000 9999
>> mpls label protocol ldp
>> call rsvp-sync
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> interface Tunnel98
>> ip unnumbered Loopback0
>> tunnel source Loopback0
>> tunnel destination 32.32.0.8
>> tunnel mode mpls traffic-eng
>> tunnel mpls traffic-eng autoroute announce
>> tunnel mpls traffic-eng autoroute metric relative -1
>> tunnel mpls traffic-eng priority 7 7
>> tunnel mpls traffic-eng bandwidth 500
>> tunnel mpls traffic-eng path-option 10 dynamic
>> no clns route-cache
>> !
>> interface Loopback0
>> ip address 32.32.0.9 255.255.255.255
>> ip router isis
>> isis circuit-type level-1
>> !
>> !
>> interface FastEthernet0/0.29
>> encapsulation dot1Q 29
>> ip address 39.39.29.9 255.255.255.0
>> ip router isis
>> mpls ip
>> isis network point-to-point
>> isis csnp-interval 10
>> !
>> interface FastEthernet0/0.79
>> encapsulation dot1Q 79
>> ip address 39.39.79.9 255.255.255.0
>> ip router isis
>> mpls traffic-eng tunnels
>> mpls ip
>> isis network point-to-point
>> isis csnp-interval 10
>> ip rsvp bandwidth 2000
>>
>> !
>> router isis
>> net 52.0009.0000.0000.0009.00
>> is-type level-1
>> metric-style wide
>> mpls traffic-eng router-id Loopback0
>> mpls traffic-eng level-1
>>
>>
>>
>>
>> R8
>> mpls traffic-eng tunnels
>> no mpls traffic-eng auto-bw timers frequency 0
>> mpls ldp router-id Loopback0
>> mpls label range 8000 8999
>> mpls label protocol ldp
>> call rsvp-sync
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> interface Tunnel89
>> ip unnumbered Loopback0
>> tunnel source Loopback0
>> tunnel destination 32.32.0.9
>> tunnel mode mpls traffic-eng
>> tunnel mpls traffic-eng autoroute announce
>> tunnel mpls traffic-eng priority 7 7
>> tunnel mpls traffic-eng bandwidth 500
>> tunnel mpls traffic-eng path-option 10 dynamic
>> no clns route-cache
>> !
>> interface Loopback0
>> ip address 32.32.0.8 255.255.255.255
>> ip router isis
>> !
>> !
>> interface FastEthernet1/0
>> no ip address
>> duplex full
>> speed auto
>> !
>> interface FastEthernet1/0.28
>> encapsulation dot1Q 28
>> ip address 39.39.28.8 255.255.255.0
>> ip router isis
>> mpls traffic-eng tunnels
>> mpls ip
>> isis circuit-type level-1
>> isis network point-to-point
>> isis csnp-interval 10
>> ip rsvp bandwidth 1000
>> !
>> !
>> interface FastEthernet1/0.78
>> encapsulation dot1Q 78
>> ip address 39.39.78.8 255.255.255.0
>> ip router isis
>> mpls ip
>> isis circuit-type level-1
>> isis hello-interval minimal
>> isis network point-to-point
>> no isis hello padding
>> isis csnp-interval 10
>> !
>> router isis
>> net 52.0009.0000.0000.0008.00
>> is-type level-1
>> metric-style wide
>>
>>
>>
>> R2 and R7
>> both have
>> !
>> router isis
>> net 52.0009.0000.0000.000X.00 --- X is based on their local Router
>> number
>> is-type level-1
>> metric-style wide
>> mpls traffic-eng router-id Loopback0
>> mpls traffic-eng level-1
>> On the subinterfaces
>> R2 - .28 and .27 has the ip rsvp band 1000
>> R7 - .27 and .79 has the ip rsvp band 1000
>>
>> I started with 5000 and 2000 on the tunnel but after the recommendation to
>> lower it, I tried lowering it but didnt help.
>> Here is the sh mpls traff topo
>> Rack1R8#
>> Rack1R8#show mpls traffic-eng topology
>> My_System_id: 0000.0000.0008.00 (isis level-1)
>> Signalling error holddown: 10 sec Global Link Generation 15
>> IGP Id: 0000.0000.0002.00, MPLS TE Id:32.32.0.2 Router Node (isis
>> level-1)
>> link[0]: Point-to-Point, Nbr IGP Id: 0000.0000.0008.00,
>> nbr_node_id:1, gen:5
>> frag_id 0, Intf Address:39.39.28.2, Nbr Intf Address:39.39.28.8
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 10000 (kbps), max_reservable_bw_global: 2000 (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 2000 0
>> bw[1]: 0 2000 0
>> bw[2]: 0 2000 0
>> bw[3]: 0 2000 0
>> bw[4]: 0 2000 0
>> bw[5]: 0 2000 0
>> bw[6]: 0 2000 0
>> bw[7]: 0 2000 0
>> link[1]: Point-to-Point, Nbr IGP Id: 0000.0000.0007.00,
>> nbr_node_id:2, gen:5
>> frag_id 0, Intf Address:39.39.27.2, Nbr Intf Address:39.39.27.7
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 10000 (kbps), max_reservable_bw_global: 2000 (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 2000 0
>> bw[1]: 0 2000 0
>> bw[2]: 0 2000 0
>> bw[3]: 0 2000 0
>> bw[4]: 0 2000 0
>> bw[5]: 0 2000 0
>> bw[6]: 0 2000 0
>> bw[7]: 0 2000 0
>> IGP Id: 0000.0000.0007.00, MPLS TE Id:32.32.0.7 Router Node (isis
>> level-1)
>>
>> IGP Id: 0000.0000.0008.00, MPLS TE Id:32.32.0.8 Router Node (isis
>> level-1)
>> link[0]: Point-to-Point, Nbr IGP Id: 0000.0000.0002.00,
>> nbr_node_id:3, gen:15
>> frag_id 0, Intf Address:39.39.28.8, Nbr Intf Address:39.39.28.2
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 100000 (kbps), max_reservable_bw_global: 1000
>> (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 1000 0
>> bw[1]: 0 1000 0
>> bw[2]: 0 1000 0
>> bw[3]: 0 1000 0
>> bw[4]: 0 1000 0
>> bw[5]: 0 1000 0
>> bw[6]: 0 1000 0
>> bw[7]: 0 1000 0
>> IGP Id: 0000.0000.0009.00, MPLS TE Id:32.32.0.9 Router Node (isis
>> level-1)
>> link[0]: Point-to-Point, Nbr IGP Id: 0000.0000.0007.00,
>> nbr_node_id:2, gen:4
>> frag_id 0, Intf Address:39.39.79.9, Nbr Intf Address:39.39.79.7
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 100000 (kbps), max_reservable_bw_global: 2000
>> (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 2000 0
>> bw[1]: 0 2000 0
>> bw[2]: 0 2000 0
>> bw[3]: 0 2000 0
>> bw[4]: 0 2000 0
>> bw[5]: 0 2000 0
>> bw[6]: 0 2000 0
>> bw[7]: 0 2000 0
>>
>>
>>
>>
>> Rack1R9#sh mpls traffic-eng ?
>> autoroute Autorouted tunnel destination information
>> forwarding-adjacency forwarding-adjacency tunnel destination
>> information
>> link-management Link Management information
>> topology Show topology Commands
>> tunnels MPLS traffic-eng tunnel status
>> Rack1R9#sh mpls traffic-eng topo
>> My_System_id: 0000.0000.0009.00 (isis level-1)
>> Signalling error holddown: 10 sec Global Link Generation 12
>> IGP Id: 0000.0000.0002.00, MPLS TE Id:32.32.0.2 Router Node (isis
>> level-1)
>> link[0]: Point-to-Point, Nbr IGP Id: 0000.0000.0008.00,
>> nbr_node_id:4, gen:6
>> frag_id 0, Intf Address:39.39.28.2, Nbr Intf Address:39.39.28.8
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 10000 (kbps), max_reservable_bw_global: 2000 (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 2000 0
>> bw[1]: 0 2000 0
>> bw[2]: 0 2000 0
>> bw[3]: 0 2000 0
>> bw[4]: 0 2000 0
>> bw[5]: 0 2000 0
>> bw[6]: 0 2000 0
>> bw[7]: 0 2000 0
>> link[1]: Point-to-Point, Nbr IGP Id: 0000.0000.0007.00,
>> nbr_node_id:3, gen:6
>> frag_id 0, Intf Address:39.39.27.2, Nbr Intf Address:39.39.27.7
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 10000 (kbps), max_reservable_bw_global: 2000 (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 2000 0
>> bw[1]: 0 2000 0
>> bw[2]: 0 2000 0
>> bw[3]: 0 2000 0
>> bw[4]: 0 2000 0
>> bw[5]: 0 2000 0
>> bw[6]: 0 2000 0
>> bw[7]: 0 2000 0
>> IGP Id: 0000.0000.0007.00, MPLS TE Id:32.32.0.7 Router Node (isis
>> level-1)
>>
>> IGP Id: 0000.0000.0008.00, MPLS TE Id:32.32.0.8 Router Node (isis
>> level-1)
>> link[0]: Point-to-Point, Nbr IGP Id: 0000.0000.0002.00,
>> nbr_node_id:2, gen:12
>> frag_id 0, Intf Address:39.39.28.8, Nbr Intf Address:39.39.28.2
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 100000 (kbps), max_reservable_bw_global: 1000
>> (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 1000 0
>> bw[1]: 0 1000 0
>> bw[2]: 0 1000 0
>> bw[3]: 0 1000 0
>> bw[4]: 0 1000 0
>> bw[5]: 0 1000 0
>> bw[6]: 0 1000 0
>> bw[7]: 0 1000 0
>> IGP Id: 0000.0000.0009.00, MPLS TE Id:32.32.0.9 Router Node (isis
>> level-1)
>> link[0]: Point-to-Point, Nbr IGP Id: 0000.0000.0007.00,
>> nbr_node_id:-1, gen:1
>> frag_id 0, Intf Address:39.39.79.9, Nbr Intf Address:39.39.79.7
>> TE metric:10, IGP metric:10, attribute flags:0x0
>> physical_bw: 100000 (kbps), max_reservable_bw_global: 2000
>> (kbps)
>> max_reservable_bw_sub: 0 (kbps)
>> Global Pool Sub Pool
>> Total Allocated Reservable Reservable
>> BW (kbps) BW (kbps) BW (kbps)
>> --------------- ----------- ----------
>> bw[0]: 0 2000 0
>> bw[1]: 0 2000 0
>> bw[2]: 0 2000 0
>> bw[3]: 0 2000 0
>> bw[4]: 0 2000 0
>> bw[5]: 0 2000 0
>> bw[6]: 0 2000 0
>> bw[7]: 0 2000 0
>>
>> Thanks again for all your help and responses I do very much so appreciate
>> it.
>> Regards,
>> James
>>
>> -----Original Message-----
>> From: Bryan Bartik <bbartik_at_ipexpert.com>
>> To: Shawn Zandi <szmetal_at_gmail.com>
>> Cc: armylegionmedic_at_aol.com; nilsi2002_at_gmail.com; divinjohn_at_gmail.com;
>> vsrinivas.paturi_at_gmail.com; ccielab_at_groupstudy.com
>> Sent: Fri, Oct 30, 2009 10:43 am
>> Subject: Re: MPLS Traffic-Engineering Dynamic Tunnel
>>
>> "No path to destination" can be misleading because it does not really
>> mean there is no route. It just means it cannot calculate a path that meets
>> the requirements of the tunnel. I am curious to see the full configs as well
>> as "show mpls traffic-eng topology."
>>
>> On Fri, Oct 30, 2009 at 9:29 AM, Shawn Zandi <szmetal_at_gmail.com> wrote:
>>>
>>> Army,
>>> Last Error: PCALC:: No path to destination, 0000.0000.0008.00
>>> Last Error: PCALC:: No path to destination, 0000.0000.0009.00
>>>
>>> R8 does not have route to loopback of R9, and R9 does not have route to
>>> loopback of R8. Enable ISIS on loopbacks by "ip router isis" or change
>>> your
>>> TE router-ID to reachable ones.
>>>
>>> --
>>> Sincerely,
>>> Shawn Zandi
>>> Network Architect and Consultant
>>> Cisco Certified CCIE x2 (R&S, Security)
>>> Juniper, Foundry, Brocade and Procurve Certified
>>>
>>> http://blog.shafagh.com
>>>
>>>
>>>
>>> On Fri, Oct 30, 2009 at 6:45 PM, <armylegionmedic_at_aol.com> wrote:
>>>
>>> > Hello Rich,
>>> >
>>> >
>>> > Thank you very much for the response. The command metric-style wide
>>> > is
>>> > in
>>> > all the routers. When I type the command mpls traffic-eng level-* it
>>> > will
>>> > always tell me if there is no metric-style wide initiated. I have also
>>> > gone
>>> > through and checked all the routers.
>>> >
>>> >
>>> > Regards,
>>> >
>>> >
>>> > James
>>> >
>>> >
>>> > -----Original Message-----
>>> > From: Rich Collins <nilsi2002_at_gmail.com>
>>> > To: Divin Mathew John <divinjohn_at_gmail.com>
>>> > Cc: srinivas pv <vsrinivas.paturi_at_gmail.com>; armylegionmedic_at_aol.com;
>>> > ccielab_at_groupstudy.com
>>> > Sent: Fri, Oct 30, 2009 7:07 am
>>> > Subject: Re: MPLS Traffic-Engineering Dynamic Tunnel
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> > Hi,
>>> >
>>> > Your problem is that all isis router instances should be metric-style
>>> > wide for traffic engineering.
>>> >
>>> > If you do a show ip route isis you are probably missing some
>>> > destinations (for the same above reason).
>>> >
>>> > -Rich
>>> >
>>> >
>>> >
>>> >
>>> > > On Fri, Oct 30, 2009 at 9:00 AM, srinivas pv
>>> > <vsrinivas.paturi_at_gmail.com>wrote:
>>> > >
>>> > >> Hi,
>>> > >>
>>> > >> You are getting following error:
>>> > >> Path Option 10:
>>> > >> Last Error: PCALC:: No path to destination, 0000.0000.0008.00
>>> > >>
>>> > >> You can check why you are getting this.
>>> > >> Can you give following show outputs from both R8 and R9
>>> > >>
>>> > >> show mpls traffic-eng topology brief
>>> > >> show mpls traffic-eng tunnels topology path destination <tunnel dest
>>> > addr>
>>> > >> show mpls traffic-eng tunnels topology path destination <tunnel dest
>>> > addr>
>>> > >> bandwidth
>>> > >> show mpls traffic-eng tunnels topology path destination <tunnel dest
>>> > addr>
>>> > >> priority
>>> > >> show mpls traffic-eng tunnels topology path tunnel89
>>> > >> show mpls traffic-eng tunnels topology path tunnel89 bandwidth
>>> > >> show mpls traffic-eng tunnels topology path tunnel89 priority
>>> > >>
>>> > >>
>>> > >> Thanks,
>>> > >> Srinivas
>>> > >>
>>> > >>
>>> > >> On Fri, Oct 30, 2009 at 6:12 AM, <armylegionmedic_at_aol.com> wrote:
>>> > >>
>>> > >> > Hello Experts,
>>> > >> >
>>> > >> > I have been troubleshooting this for like 2 hours now and just
>>> > cannot
>>> > >> see
>>> > >> > what is wrong. I have read through the IPExpert article and tried
>>> > >> > the
>>> > >> auto
>>> > >> > bw
>>> > >> > commands and it made no difference. Also, I am able to ping
>>> > >> > perfectly
>>> > >> fine.
>>> > >> > I
>>> > >> > am trying to go R8-R2-R7-R9 and reverse path back, but my tunnel
>>> > >> > on R8
>>> > >> and
>>> > >> > R9
>>> > >> > will not come online. I have also lowered the bandwidth on the
>>> > >> > RSVP as
>>> > >> well
>>> > >> > as
>>> > >> > on the tunnel and this didnt help.
>>> > >> >
>>> > >> > Here is the config:
>>> > >> >
>>> > >> > R2
>>> > >> > mpls traffic-eng tunn
>>> > >> > router isis
>>> > >> > mpls traffic-eng level-1
>>> > >> > mpls traffic-eng rou lo0
>>> > >> > int e0/0.28
>>> > >> > mpls traffic-eng tunn
>>> > >> > ip rsvp band 5000
>>> > >> > int e0/0.27
>>> > >> > mpls traffic-eng tunn
>>> > >> > ip rsvp band 5000
>>> > >> > r7
>>> > >> > mpls traffic-eng tunn
>>> > >> > router isis
>>> > >> > mpls traffic-eng rout lo0
>>> > >> > mpls traffic-eng level-1
>>> > >> > int f1/0.27
>>> > >> > mpls traffic-eng tunn
>>> > >> > ip rsvp band 5000
>>> > >> > int f1/0.79
>>> > >> > mpls traffic-eng tunn
>>> > >> > ip rsvp band 5000
>>> > >> > r8
>>> > >> > mpls traffic-eng tunn
>>> > >> > router isis
>>> > >> > mpls traffic-eng rou lo0
>>> > >> > mpls traffic-eng level-1
>>> > >> > int f1/0.28
>>> > >> > mpls traffic-eng tunn
>>> > >> > ip rsvp band 5000
>>> > >> > int tunn 89
>>> > >> > ip unn lo0
>>> > >> > tunn so lo0
>>> > >> > tunn dest 32.32.0.9
>>> > >> > tunn mode mpls traffic-eng
>>> > >> > tunn mpls traffic-eng prio 7 7
>>> > >> > tunn mpls traffic-eng band 2000
>>> > >> > tunn mpls traffic-eng path-opt 10 dynamic
>>> > >> > tunn mpls traffic-eng autoroute announce
>>> > >> > r9
>>> > >> > mpls traffic-eng tunn
>>> > >> > router isis
>>> > >> > metric-sty wide
>>> > >> > mpls traffic-eng rou lo0
>>> > >> > mpls traffic-eng level-1
>>> > >> > int f1/0.79
>>> > >> > mpls traffic-eng tunn
>>> > >> > ip rsvp band 5000
>>> > >> > int tunn 98
>>> > >> > ip unn lo0
>>> > >> > tunn so lo0
>>> > >> > tunn dest 32.32.0.8
>>> > >> > tunn mode mpls traffic-eng
>>> > >> > tunn mpls traffic-eng prio 7 7
>>> > >> > tunn mpls traffic-eng band 2000
>>> > >> > tunn mpls traffic-eng path-opt 10 dynamic
>>> > >> > tunn mpls traffic-eng autoroute announce
>>> > >> >
>>> > >> > If I do a sh mpls traff tunn I get
>>> > >> >
>>> > >> > R9
>>> > >> >
>>> > >> > Rack1R9(config-if)#do sh mpls traffi tunn
>>> > >> > Name: Rack1R9_t98 (Tunnel98) Destination:
>>> > >> 32.32.0.8
>>> > >> > Status:
>>> > >> > Admin: up Oper: down Path: not valid Signalling:
>>> > >> > Down
>>> > >> > path option 10, type dynamic
>>> > >> > Config Parameters:
>>> > >> > Bandwidth: 2000 kbps (Global) Priority: 7 7 Affinity:
>>> > >> > 0x0/0xFFFF
>>> > >> > Metric Type: TE (default)
>>> > >> > AutoRoute: enabled LockDown: disabled Loadshare: 500
>>> > bw-based
>>> > >> > auto-bw: disabled
>>> > >> > History:
>>> > >> > Tunnel:
>>> > >> > Time since created: 32 minutes, 28 seconds
>>> > >> > Path Option 10:
>>> > >> > Last Error: PCALC:: No path to destination, 0000.0000.0008.00
>>> > >> >
>>> > >> > R8
>>> > >> > Rack1R8(config-if)#do sh mpls traffi tunn
>>> > >> > Name: Rack1R8_t89 (Tunnel89) Destination:
>>> > >> 32.32.0.9
>>> > >> > Status:
>>> > >> > Admin: up Oper: down Path: not valid Signalling:
>>> > >> > Down
>>> > >> > path option 10, type dynamic
>>> > >> > Config Parameters:
>>> > >> > Bandwidth: 500 kbps (Global) Priority: 7 7 Affinity:
>>> > >> 0x0/0xFFFF
>>> > >> > Metric Type: TE (default)
>>> > >> > AutoRoute: enabled LockDown: disabled Loadshare: 500
>>> > bw-based
>>> > >> > auto-bw: disabled
>>> > >> > History:
>>> > >> > Tunnel:
>>> > >> > Time since created: 33 minutes, 15 seconds
>>> > >> > Path Option 10:
>>> > >> > Last Error: PCALC:: No path to destination, 0000.0000.0009.00
>>> > >> > Rack1R8(config-if)#
>>> > >> >
>>> > >> > TIA for any help.
>>> > >> >
>>> > >> > Regards,
>>> > >> >
>>> > >> > James
>>> > >> >
>>> > >> >
>>> > >> > Blogs and organic groups at http://www.ccie.net
>>> > >> >
>>> > >> >
>>> > _______________________________________________________________________
>>> > >> > Subscription information may be found at:
>>> > >> > http://www.groupstudy.com/list/CCIELab.html
>>> > >>
>>> > >>
>>> > >> Blogs and organic groups at http://www.ccie.net
>>> > >>
>>> > >>
>>> > >> _______________________________________________________________________
>>> > >> Subscription information may be found at:
>>> > >> http://www.groupstudy.com/list/CCIELab.html
>>> > >>
>>> > >>
>>> > >>
>>> > >>
>>> > >>
>>> > >>
>>> > >>
>>> > >>
>>> > >
>>> > >
>>> > > --
>>> > >
>>> > > Sent from Karnataka, India
>>> > > Jean Cocteau <http://www.quotationspage.com/quote/1031.html> - "We
>>> > > must
>>> > > believe in luck. For how else can we explain the success of those we
>>> > don't
>>> > > like?"
>>> > >
>>> > >
>>> > > Blogs and organic groups at http://www.ccie.net
>>> > >
>>> > >
>>> > > _______________________________________________________________________
>>> > > Subscription information may be found at:
>>> > > http://www.groupstudy.com/list/CCIELab.html
>>> >
>>> >
>>> > Blogs and organic groups at http://www.ccie.net
>>> >
>>> > _______________________________________________________________________
>>> > Subscription information may be found at:
>>> > http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
>> --
>> Bryan Bartik
>> CCIE #23707 (R&S), CCNP
>> Sr. Support Engineer - IPexpert, Inc.
>> URL: http://www.IPexpert.com
>
>
>
> --
> Bryan Bartik
> CCIE #23707 (R&S), CCNP
> Sr. Support Engineer - IPexpert, Inc.
> URL: http://www.IPexpert.com

Blogs and organic groups at http://www.ccie.net
Received on Sat Oct 31 2009 - 10:04:27 ART