Re: Help Voice Experts!! QSIG Decode command

Hi RF,

Here's the config. The cisco gw is connected to an ericsson pbx via qsig
trunk and to the avaya cm via h323 trunk. I have tried the command you've
suggested but no results and googling around suggest using the qsig decode
command to parse the caller ID between systems.

Hi Karl, it's not IP-IP. PA is PA-VXC-2T1E1+

------------------------------------------------------------------
isdn switch-type primary-qsig
!
voice call carrier capacity active
!
voice service voip
allow-connections h323 to h323
signaling forward unconditional
!
fax interface-type fax-mail
!
controller E1 1/0
 framing NO-CRC4
 pri-group timeslots 1-12,16
 description Ericsson Qsig link
!
interface Loopback0
 description loop back for gateway
 ip address <>
 h323-gateway voip interface
 h323-gateway voip id GW1 ipaddr <>
 h323-gateway voip tech-prefix 1#
 h323-gateway voip bind srcaddr <>
!
interface FastEthernet0/0
 description Connection to LAN
 ip address <>
 speed 100
 full-duplex
!
interface Serial0/0
 no ip address
 no ip mroute-cache
 shutdown
 clock rate 2000000
!
interface FastEthernet0/1
 no ip address
 load-interval 30
 shutdown
 speed 100
 full-duplex
 no cdp enable
 max-reserved-bandwidth 95
!
interface Serial0/1
 no ip address
 no ip mroute-cache
 load-interval 30
 shutdown
 clock rate 2000000
!
interface Serial1/0:15
 no ip address
 encapsulation hdlc
 no logging event link-status
 isdn switch-type primary-qsig
 isdn network-failure-cause 34
 isdn protocol-emulate network
 isdn incoming-voice voice
 no cdp enable
!
router eigrp 100
 network 10.0.0.0
 auto-summary
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
voice-port 1/0:15
 echo-cancel coverage 32
!
mgcp behavior g729-variants static-pt
!
dial-peer cor custom
!
dial-peer voice 1 voip
 description catch all
 destination-pattern .
 session target ras
 no vad
!
dial-peer voice 99 pots
 description 9900 to 9999
 destination-pattern 99..
 direct-inward-dial
 port 1/0:15
 forward-digits 4
 no register e164
!
dial-peer voice 10 voip
 destination-pattern 123..
 session target ras
 incoming called-number 12..
 codec g711ulaw
!
gateway
 timer receive-rtp 1200
 emulate cisco h323 bandwidth
!
!

On Tue, Jun 29, 2010 at 12:28 AM, Radioactive Frog <pbhatkoti_at_gmail.com>wrote:

> Hi Emir,
> Please post your config. and provide more detail about your setup.
>
> make sure you've below command:
> on cisco gw:
>
> Serial0/0/1 (or whatever)
>
> isdn supp-service name calling
>
> --frog
>
> On Mon, Jun 28, 2010 at 8:25 AM, emir d souza <emir979_at_gmail.com> wrote:
>
>> Hi,
>>
>> I'm trying to find out if this command is IOS or platform dependant. I'm
>> running IOS 12.4 (c7200-jk9s-mz.124-25b) and I can't see this command on
>> my
>> router, and yet it's in the Cisco documentation !!
>>
>> Unless there is another way of doing this, I'm running a Cisco GW in
>> between
>> an Ericsson PBX and a Avaya Communications Manager, the problem now is
>> parsing the Caller ID between the two phone systems.
>>
>>
>> R1(conf-serv-h323)#?
>> VOICE SERVICE VOIP H323 configuration commands:
>> bearercap-ie Specify bearercap_ie coding
>> billing B-channel info present
>> call Global setting for H.323 Calls
>> default Set a command to its defaults
>> emptycapability Empty Capability (TCS=0)
>> encoding Global setting for H.323 ASN.1 encoding options
>> exit Exit from voice service voip h323 configuration mode
>> h225 TCP H225 call signalling channel
>> h245 H245 Signalling
>> h450 H450 parameter configuration
>> no Negate a command or set its defaults
>> ras Gateway RAS configuration
>> session H323 Voice Protocol session config
>> telephony-service For CCME H323 connections
>>
>>
>> Appreciate your help guys!!
>>
>>
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Jun 29 2010 - 11:20:25 ART