ipv6 multicast

Hi all

I tried to configure ipv6 multicast as shown below but suddenly two tunnel
interface came up and I can not announce my RP to my bsr which is
diffenrent boxes.I went to the solution gu;de of lab nothing mentioned
there.What did i wrong?

When I did debug it told me no pim neighbor has been found.Do I have to
enable sometihng?
AFAIK pim is automaticly is enabled once I run ipv6 multicast routing

Rack1R4#sh ipv6 int brief
FastEthernet0/0 [up/up]
Serial0/0 [up/up]
FastEthernet0/1 [up/up]
    FE80::C000:1BFF:FE10:1
    2001:CC1E:1:404:C000:1BFF:FE10:1
Serial0/1 [administratively down/down]
Loopback0 [up/up]
Tunnel0 [up/up]
    FE80::C000:1BFF:FE10:0
    unnumbered (FastEthernet0/1)
Tunnel45 [up/up]
    FE80::9601:404
    2001:CC1E:4545::4
Rack1R4#
Rack1R4#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Rack1R4(config)#ip pi
Rack1R4(config)#ipv
Rack1R4(config)#ipv6 pi
Rack1R4(config)#ipv6 pim b
Rack1R4(config)#ipv6 pim bsr ?
  candidate Configure BSR related candidates

Rack1R4(config)#ipv6 pim bsr c
Rack1R4(config)#ipv6 pim bsr candidate ?
  bsr Configure Candidate BSR
  rp Configure Candidate RP
Rack1R4(config)#ipv6 pim bsr candidate r
Rack1R4(config)#ipv6 pim bsr candidate rp 2001:CC1E:1:404:C000:1BFF:FE10:1
Rack1R4(config)#
*Mar 1 04:58:48.914: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel1, changed state to down
*Mar 1 04:58:48.942: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel2, changed state to down
Rack1R4(config)#
*Mar 1 04:58:58.902: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel1, changed state to up
*Mar 1 04:58:58.930: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel2, changed state to up
Rack1R4(config)#end
Rack1R4#sh i
*Mar 1 05:00:46.150: %SYS-5-CONFIG_I: Configured from console by console
Rack1R4#sh int tu
Rack1R4#sh int tunnel 1
Tunnel1 is up, line protocol is up
  Hardware is Tunnel
  MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  Keepalive not set
  Tunnel source 2001:CC1E:1:404:C000:1BFF:FE10:1 (FastEthernet0/1),
destination 2001:CC1E:1:404:C000:1BFF:FE10:1
  Tunnel protocol/transport PIM/IPv6
  Tunnel TTL 255
  Tunnel is transmit only
  Tunnel transmit bandwidth 8000 (kbps)
  Tunnel receive bandwidth 8000 (kbps)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

Rack1R4#sh int tunnel 2
Tunnel2 is up, line protocol is up
  Hardware is Tunnel
  MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  Keepalive not set
  Tunnel source 2001:CC1E:1:404:C000:1BFF:FE10:1 (FastEthernet0/1),
destination 2001:CC1E:1:404:C000:1BFF:FE10:1
  Tunnel protocol/transport PIM/IPv6
  Tunnel TTL 255
  Tunnel is receive only
  Tunnel transmit bandwidth 8000 (kbps)
  Tunnel receive bandwidth 8000 (kbps)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
Rack1R4#
Rack1R4#
Rack1R4#
Rack1R4#

Rack1R4#sh ipv6 int brief
FastEthernet0/0 [up/up]
Serial0/0 [up/up]
FastEthernet0/1 [up/up]
    FE80::C000:1BFF:FE10:1
    2001:CC1E:1:404:C000:1BFF:FE10:1
Serial0/1 [administratively down/down]
Loopback0 [up/up]
Tunnel0 [up/up]
    FE80::C000:1BFF:FE10:0
    unnumbered (FastEthernet0/1)
Tunnel45 [up/up]
    FE80::9601:404
    2001:CC1E:4545::4
Rack1R4#
Rack1R4#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Rack1R4(config)#ip pi
Rack1R4(config)#ipv
Rack1R4(config)#ipv6 pi
Rack1R4(config)#ipv6 pim b
Rack1R4(config)#ipv6 pim bsr ?
  candidate Configure BSR related candidates
Rack1R4(config)#ipv6 pim bsr c
Rack1R4(config)#ipv6 pim bsr candidate ?
  bsr Configure Candidate BSR
  rp Configure Candidate RP
Rack1R4(config)#ipv6 pim bsr candidate r
Rack1R4(config)#ipv6 pim bsr candidate rp 2001:CC1E:1:404:C000:1BFF:FE10:1
Rack1R4(config)#
*Mar 1 04:58:48.914: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel1, changed state to down
*Mar 1 04:58:48.942: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel2, changed state to down
Rack1R4(config)#
*Mar 1 04:58:58.902: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel1, changed state to up
*Mar 1 04:58:58.930: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Tunnel2, changed state to up
Rack1R4(config)#end
Rack1R4#sh i
*Mar 1 05:00:46.150: %SYS-5-CONFIG_I: Configured from console by console
Rack1R4#sh int tu
Rack1R4#sh int tunnel 1
Tunnel1 is up, line protocol is up
  Hardware is Tunnel
  MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  Keepalive not set
  Tunnel source 2001:CC1E:1:404:C000:1BFF:FE10:1 (FastEthernet0/1),
destination 2001:CC1E:1:404:C000:1BFF:FE10:1
  Tunnel protocol/transport PIM/IPv6
  Tunnel TTL 255
  Tunnel is transmit only
  Tunnel transmit bandwidth 8000 (kbps)
  Tunnel receive bandwidth 8000 (kbps)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

Rack1R4#sh int tunnel 2
Tunnel2 is up, line protocol is up
  Hardware is Tunnel
  MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation TUNNEL, loopback not set
  Keepalive not set
  Tunnel source 2001:CC1E:1:404:C000:1BFF:FE10:1 (FastEthernet0/1),
destination 2001:CC1E:1:404:C000:1BFF:FE10:1
  Tunnel protocol/transport PIM/IPv6
  Tunnel TTL 255
  Tunnel is receive only
  Tunnel transmit bandwidth 8000 (kbps)
  Tunnel receive bandwidth 8000 (kbps)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/0 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
Rack1R4#

Rack1R4#
*Mar 1 05:06:49.294: IPv6 BSR: Building C-RP Adv for
2001:CC1E:1:404:C000:1BFF:FE10:1, priority 192, holdtime 150
*Mar 1 05:06:49.294: IPv6 BSR: Adding group prefix FF00::/8 to C-RP Adv
*Mar 1 05:06:49.294: IPv6 BSR: Sending C-RP Advertisement for
2001:CC1E:1:404:C000:1BFF:FE10:1 to 2001:CC1E:1:404:C000:1BFF:FE10:1
*Mar 1 05:06:49.302: IPv6 BSR: Received C-RP Advertisement from
2001:CC1E:1:404:C000:1BFF:FE10:1, priority 192 holdtime 150, prefix count 1
*Mar 1 05:06:49.306: IPv6 BSR: Updating C-RP cache for
2001:CC1E:1:404:C000:1BFF:FE10:1
*Mar 1 05:06:49.310: IPv6 BSR: Updated received range FF00::/8, mode Sparse
*Mar 1 05:06:49.510: IPv6 BSR: Originating BSM for
2001:CC1E:1:404:C000:1BFF:FE10:1, priority 100 hash mask length 126
*Mar 1 05:06:49.514: IPv6 BSR: Adding Group prefix FF00::/8, RP count 1,
Frag RP count 1
*Mar 1 05:06:49.518: IPv6 BSR: Adding RP 2001:CC1E:1:404:C000:1BFF:FE10:1,
Priority 192, Holdtime 150
*Mar 1 05:06:49.522: IPv6 BSR: Skipping interf
Rack1R4#ace Loopback0, no PIM neighbors found
*Mar 1 05:06:49.526: IPv6 BSR: Skipping interface FastEthernet0/0, no PIM
neighbors found
*Mar 1 05:06:49.526: IPv6 BSR: Skipping interface FastEthernet0/1, no PIM
neighbors found
*Mar 1 05:06:49.530: IPv6 BSR: Skipping interface Serial0/0, no PIM
neighbors found
*Mar 1 05:06:49.534: IPv6 BSR: Skipping interface Serial0/1, no PIM
neighbors found
*Mar 1 05:06:49.534: IPv6 BSR: Sending BSR message on interface Tunnel45
*Mar 1 05:06:49.538: IPv6 BSR: Skipping interface Tunnel0, no PIM neighbors
found
*Mar 1 05:06:49.542: IPv6 BSR: Skipping interface Tunnel1, no PIM neighbors
found
*Mar 1 05:06:49.546: IPv6 BSR: Skipping interface Tunnel2, no PIM neighbors
found
*Mar 1 05:06:49.546: IPv6 BSR: Recieved Group range FF00::/8, RP count 1
Fragment RP count1
*Mar 1 05:06:49.550: IPv6 BSR: Update RP 2001:CC1E:1:404:C000:1BFF:FE10:1,
Holdtime 150, Priority 192

Blogs and organic groups at http://www.ccie.net
Received on Sat Aug 21 2010 - 01:44:04 ART