Re: 2511 ACCESS SERVER

ya i did that pressing (ctrl x).its not working

i attached only one octal cable at 1-8 lines port in 2511 access server and
 attach only 1 and 2 to R1 & R2 to test.

and i took console of 2511 and trying all that config.....

Please tell me what to do...?

thanks
Achal

On Thu, Jun 16, 2011 at 9:51 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar>wrote:

> Achal,
> it's not "hanging", it's connected.
> You can tell by entereing the escape sequence (ctl-^ x) and you
> should get the router prompt again.
>
> The 2511 has 2 octal cables, one for 1-8 and the other for 9-16.
> They might have RJ-45 or DB25. They should be labeled 1 to 8.
>
> Is the other end connected to something ? You can try to connect
> to a com port and see if your link is working each way.
> You will not see echo! May be some port is fried, so test each
> one and single the working ones, if that's the case.
>
> -Carlos
>
> ACHAL GUPTA @ 16/06/2011 08:37 -0300 dixit:
>
> thanks for reply....
>>
>> My line numbers are 1 to 16 and i think its ok
>>
>> Cisco2511#sh line
>> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
>> Int
>> * 0 CTY - - - - - 0 1 0/0
>> -
>> 1 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 2 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 3 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 4 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 5 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 6 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 7 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 8 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 9 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 10 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 11 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 12 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 13 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 14 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 15 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 16 TTY 9600/9600 - - - - - 0 0 0/0
>> -
>> 17 AUX 9600/9600 - - - - - 0 0 0/0
>> -
>> 18 VTY - - - - - 0 0 0/0
>> -
>> 19 VTY - - - - - 0 0 0/0
>> -
>> 20 VTY - - - - - 0 0 0/0
>> -
>>
>> and i am trying telnet r1 and straight away r1 also but it shows the
>> following and hang i restart my router and then it comes normal
>>
>>
>> Cisco2511#telnet r1
>> Trying R1 (1.1.1.1, 2002)... Open
>>
>>
>> i dont know why it hang.... pls tell me whats wrong m i doing...?
>>
>> thanks
>> Achal
>> On Thu, Jun 16, 2011 at 8:06 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar
>> >wrote:
>>
>> ACHAL,
>>> your config is ok as long as your lines are numbered 1 to 16,
>>> which in the case of a 2511 they should. Do a show line to verify.
>>>
>>> What exactly is your problem ? Can you telnet to the reverse telnet port
>>> and get connected ? Or refused ?
>>> Connected and nothing ?
>>>
>>> -Carlos
>>>
>>>
>>> ACHAL GUPTA @ 15/06/2011 20:08 -0300 dixit:
>>>
>>> Hello Experts,
>>>
>>>> Can anyone tell me how can i make my 2511 roter as a access server?
>>>>
>>>> i tried with following config but not working.
>>>>
>>>> I gave the ip address to ethernet (172.16.1.2) and its pinging my Laptop
>>>> ip
>>>> address.
>>>>
>>>> i attach my octal cable also with no.1 cable in R1 and no.2 cable in
>>>> R2.........
>>>>
>>>> ip host R1 2001 172.16.1.2
>>>> ip host R2 2002 172.16.1.2
>>>> - - - - - -
>>>> - - - - - -
>>>>
>>>> line con 0
>>>> line 1 16
>>>> exec-timeout 0 0
>>>> no exec
>>>> transport input all
>>>> line vty 0 4
>>>> password cisco
>>>> login
>>>>
>>>>
>>>> i did that config but it is not working
>>>>
>>>> pls tell me ehat i m doing wrong and what else i will have to do?
>>>>
>>>>
>>>> --
>>> Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>>>
>>>
>>
>>
>>
> --
> Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>

-- 
*
Thanks,*
*Achal*
Blogs and organic groups at http://www.ccie.net