Any reason why I'm not seeing underlying faste interfaces and port-chan
interfaces packets counters incrementing, but do see it on svi?
Aaron
R1#sh ver | in 3700
Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version
12.4(9)T7, RELEASE SOFTWARE (fc3)
ROM: 3700 Software (C3725-ADVENTERPRISEK9-M), Version 12.4(9)T7, RELEASE
SOFTWARE (fc3)
R1#sh run in vl 100 | in ip add
ip address 1.1.1.1 255.255.255.0
R1#sh span vl 100 br
VLAN100
Spanning tree enabled protocol ieee
Root ID Priority 32768
Address c200.0840.0001
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address c200.0840.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port
ID
-------------------- ------- ---- ----- --- ----- --------------------
-------
Port-channel1 129.65 128 12 FWD 0 32768 c200.0840.0001
129.65
R1#sh int port-ch 1 | in emb
Members in this channel: Fa1/0 Fa1/1
R1#ping 1.1.1.2 re 1
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:
!
Success rate is 100 percent (1/1), round-trip min/avg/max = 44/44/44 ms
R1#sh int vl 100 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1002 packets input, 114026 bytes, 0 no buffer
1006 packets output, 114283 bytes, 0 underruns
R1#sh int port- 1 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
R1#sh int f1/0 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
R1#sh int f1/1 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
R1#ping 1.1.1.2 re 1
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:
!
Success rate is 100 percent (1/1), round-trip min/avg/max = 36/36/36 ms
R1#sh int vl 100 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1003 packets input, 114140 bytes, 0 no buffer
1007 packets output, 114397 bytes, 0 underruns
R1#sh int port- 1 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
R1#sh int f1/0 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
R1#sh int f1/1 | in pac
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
Blogs and organic groups at http://www.ccie.net
Received on Wed Jun 20 2012 - 10:29:50 ART
This archive was generated by hypermail 2.2.0 : Sun Jul 01 2012 - 10:39:52 ART