Re: OSPF on 32 bit dialer interface

I have removed no peer neighbor-route and now can see /32 on both as
directly connected but still the OSPF adj is not coming up. I am using GNS3
with adv enterprise (c3745-adventerprisek9-mz.124-25d.bin). I don't think
its a GNS3 issue.
Regards

On 28 November 2012 14:08, Joe Sanchez <marco207p_at_gmail.com> wrote:

> There are issues with different devices that will not allow the is of to
> work properly with the PPPoe without using a dhcp pool on the server side.
> What code and platform are you using. Try GNS3 on the 7200 platform it
> works fine.
>
> Regards,
> Joe Sanchez
>
> ( please excuse the brevity of this email as it was sent via a mobile
> device. Please excuse misspelled words or sentence structure.)
>
> On Nov 28, 2012, at 5:03 AM, Tauseef Khan <tasneemjan_at_googlemail.com>
> wrote:
>
> > Please find below the configs
> > server:R1
> >
> > bba-group pppoe CISCO
> > virtual-template 16
> > !
> > interface Gigabit0/0
> > no ip address
> > ip ospf network point-to-multipoint
> > ip ospf mtu-ignore
> > duplex auto
> > speed auto
> > pppoe enable group CISCO
> > end
> >
> > !
> > interface Virtual-Template16
> > mtu 1492
> > ip address 172.31.255.1 255.255.255.0
> > ip ospf network point-to-multipoint
> > ip ospf mtu-ignore
> > peer default ip address pool 1.6
> > ppp authentication chap
> > end
> >
> > usename R2 password pass
> >
> > ip local-pool 6.6 172.31.255.254
> >
> > __________________________________________________
> >
> > Client R2:
> > interface FastEthernet0/0
> > no ip address
> > ip ospf network point-to-multipoint
> > ip ospf mtu-ignore
> > speed auto
> > half-duplex
> > pppoe enable
> > pppoe-client dial-pool-number 16
> > !
> >
> > interface Dialer16
> > mtu 1492
> > ip address negotiated
> > encapsulation ppp
> > ip ospf network point-to-multipoint
> > dialer pool 16
> > dialer idle-timeout 0
> > dialer persistent
> > no peer neighbor-route
> > ppp chap password 0 pass
> > end
> >
> > R2:
> > sh ip ospf int br
> > Interface PID Area IP Address/Mask Cost State Nbrs
> F/C
> >
> __________________________________________________________________________
> > Di16 1 2 172.31.255.254/32 1785 P2MP
> 0/0
> >
> __________________________________________________________________________
> >
> > Kind regards
> >
> > Tauseef
> > mobile: +44 7837209187
> >
> >
> > On 28 November 2012 10:10, Mohammad Mousa <mohd-mousa_at_hotmail.com>
> wrote:
> >
> >> Post your full configs so we can check together. Did you change the MTU?
> >>
> >> --
> >> Mohammad Mousa
> >> CCIE #36990
> >>
> >>
> >>
> >>
> >>
> >>
> >> On Nov 28, 2012, at 12:28 PM, Tauseef Khan wrote:
> >>
> >>> Appreciate if some one could help. I have ospf running on 2 routers R1
> >> and
> >>> R2.
> >>> R2 is a PPPoE client and R1 is the server. R2 has a negotiated ip
> >> address
> >>> on the dialer interface from R1 which is host (/32) address while R1
> has
> >> a
> >>> /29 bit Ip address on its interface facing towards Client.
> >>> OSPF adj is not coming up between the client and Server
> >>> On client dialer int and Server int I have ip ospf network
> >>> point-to-multipoint
> >>> i also tried no peer neighbor-route on client dialer interface.
> >>>
> >>> debugs on the client side show:
> >>> OSPF: Rcv pkt from 172.31.29.1, Dialer16, area 0.0.0.3 : src not on the
> >>> same network
> >>>
> >>> I have tried changing the network type to poin-to-poitn as well but no
> >> adj
> >>>
> >>> Regards
> >>>
> >>>
> >>> Blogs and organic groups at http://www.ccie.net
> >>>
> >>> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Nov 28 2012 - 14:52:48 ART