From: Tom Young (gitsyoung@yahoo.co.jp)
Date: Mon May 31 2004 - 15:11:46 GMT-3
Look the result , still hasn't VTP mode, very strange.
C65SV-1 (enable) sh spantree 1 ac
VLAN 1
Spanning tree enabled
Spanning tree type ieee
Designated Root 00-07-eb-29-35-00
Designated Root Priority 16384
Designated Root Cost 4
Designated Root Port 3/7
Root Max Age 20 sec Hello Time 2 sec Forward Delay
15 sec
Bridge ID MAC ADDR 00-d0-02-6b-74-00
Bridge ID Priority 32768
Bridge Max Age 20 sec Hello Time 2 sec Forward Delay
15 sec
Port Vlan Port-State Cost Priority
Portfast Channel_i
------------------------ ---- ------------- ----- --------
---------- ---------
1/1 1 blocking 4 32
disabled 0
1/2 1 blocking 4 32
disabled 0
3/1 1 forwarding 4 32
disabled 0
3/2 1 forwarding 4 32
disabled 0
3/3 1 forwarding 4 32
disabled 0
3/4 1 forwarding 4 32
disabled 0
3/5 1 forwarding 4 32
disabled 0
3/6 1 forwarding 4 32
disabled 0
3/7 1 forwarding 4 32
disabled 0
3/8 1 forwarding 4 32
disabled 0
C65SV-1 (enable)
--- Georg Pauwen <pauwen@hotmail.com> $B$+$i$N%a%C%;!<%8!'(B
> Hello Tom
>
> have you tried the command:
>
>
> Console> (enable) show spantree 1 active
>
> This would show you the STP mode for VLAN 1, check
> this sample output:
>
> VLAN 1
>
> Spanning tree mode PVST+
>
> Spanning tree type ieee
>
> Spanning tree enabled
>
>
> I checked version 8.3, which has the command:
>
> set spantree mode
>
> available, which version are you running ?
>
> Regards,
>
> Georg
>
>
>
> >From: Tom Young <gitsyoung@yahoo.co.jp>
> >Reply-To: Tom Young <gitsyoung@yahoo.co.jp>
> >To: ccielab@groupstudy.com
> >Subject: Cat6509's STP mode
> >Date: Mon, 31 May 2004 10:47:28 +0900 (JST)
> >
> >Hi, group
> >
> > I type the show config command on the cat6509,
> couldn't
> >see the stp mode is either pvst or ctp. And the set
> >command also hasn't the parameter to set the mode.
> Why ?
> >
> >Thanks alot
> >
> >C65SV-1 (enable) sh spantree
> >VLAN 1
> >Spanning tree enabled
> >Spanning tree type ieee
> >
> >Designated Root 00-07-eb-29-35-00
> >Designated Root Priority 16384
> >Designated Root Cost 4
> >Designated Root Port 3/7
> >Root Max Age 20 sec Hello Time 2 sec
> Forward Delay
> >15 sec
> >
> >Bridge ID MAC ADDR 00-d0-02-6b-74-00
> >Bridge ID Priority 32768
> >Bridge Max Age 20 sec Hello Time 2 sec
> Forward Delay
> >15 sec
> >
> >Port Vlan Port-State Cost
> Priority
> >Portfast Channel_
> >------------------------ ---- ------------- -----
> --------
> >---------- --------
> >
> >C65SV-1 (enable) sh ver
> >WS-C6509 Software, Version NmpSW: 5.5(1)
> >Copyright (c) 1995-2000 by Cisco Systems
> >NMP S/W compiled on Jun 8 2000, 21:09:45
> >
> >System Bootstrap Version: 5.3(1)
> >
> >Hardware Version: 2.0 Model: WS-C6509 Serial #:
> xxxxxxxx
> >
> >Mod Port Model Serial # Versions
> >--- ---- ------------------- -----------
> >--------------------------------------
> >1 2 WS-X6K-SUP1A-2GE SAD043301GL Hw : 3.2
> > Fw :
> 5.3(1)
> > Fw1:
> 5.1(1)CSX
> > Sw :
> 5.5(1)
> > Sw1:
> 5.5(1)
> > L3 Switching Engine SAD04330MCS Hw : 1.1
> >3 8 WS-X6408A-GBIC SAL0541D4W4 Hw : 2.0
> > Fw :
> 5.4(2)
> > Sw :
> 5.5(1)
> >5 8 WS-X6408A-GBIC SAL0533AFND Hw : 2.0
> > Fw :
> 5.4(2)
> > Sw :
> 5.5(1)
> >15 1 WS-F6K-MSFC SAD04281AW3 Hw : 1.4
> > Fw :
> 12.1(1)E,
> > Sw :
> 12.1(1)E,
> >
> > DRAM FLASH
> >NVRAM
> >Module Total Used Free Total Used Free
> >Total Used Free
> >------ ------- ------- ------- ------- -------
> -------
> >----- ----- -----
> >1 65408K 38426K 26982K 16384K 6925K
> 9459K
> >512K 211K 301K
> >
> >Uptime is 19 day, 6 hours, 56 minutes
> >C65SV-1 (enable) set spantree ?
> > backbonefast Enable or disable
> fast
> >convergence
> > disable Disable spanning tree
> > enable Enable spanning tree
> > fwddelay Set spantree forward
> delay
> > hello Set spantree hello
> interval
> > maxage Set spantree max
> aging time
> > portcost Set spantree port
> cost
> > portfast Set spantree port
> fast start
> > portpri Set spantree port
> priority
> > portvlancost Set spantree port
> cost per
> >vlan
> > portvlanpri Set spantree port
> vlan
> >priority
> > priority Set spantree priority
> > root Set switch as primary
> or
> >secondary root
> > uplinkfast Enable or disable
> uplinkfast
> >groups
> >C65SV-1 (enable) set spantree ?
> >
> >__________________________________________________
> >Do You Yahoo!?
> >http://bb.yahoo.co.jp/
> >
>
>_______________________________________________________________________
> >Please help support GroupStudy by purchasing your
> study materials from:
> >http://shop.groupstudy.com
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
>
This archive was generated by hypermail 2.1.4 : Wed Jun 02 2004 - 11:12:19 GMT-3