From: Messina, John V. (john@crimsoncti.com)
Date: Mon May 31 2004 - 18:58:46 GMT-3
I believe the set spantree mode command on the 6500 with catos was first
available with version 7.1.
7.1
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_7_1/cmd_r
ef/setsn_su.htm#1058609
John Messina
-----Original Message-----
From: Tom Young [mailto:gitsyoung@yahoo.co.jp]
Sent: Sunday, May 30, 2004 9:47 PM
To: ccielab@groupstudy.com
Subject: Cat6509's STP mode
Hi, group
I type the show config command on the cat6509, couldn't
see the stp mode is either pvst or ctp. And the set
command also hasn't the parameter to set the mode. Why ?
Thanks alot
C65SV-1 (enable) sh spantree
VLAN 1
Spanning tree enabled
Spanning tree type ieee
Designated Root 00-07-eb-29-35-00
Designated Root Priority 16384
Designated Root Cost 4
Designated Root Port 3/7
Root Max Age 20 sec Hello Time 2 sec Forward Delay
15 sec
Bridge ID MAC ADDR 00-d0-02-6b-74-00
Bridge ID Priority 32768
Bridge Max Age 20 sec Hello Time 2 sec Forward Delay
15 sec
Port Vlan Port-State Cost Priority
Portfast Channel_
------------------------ ---- ------------- ----- --------
---------- --------
C65SV-1 (enable) sh ver
WS-C6509 Software, Version NmpSW: 5.5(1)
Copyright (c) 1995-2000 by Cisco Systems
NMP S/W compiled on Jun 8 2000, 21:09:45
System Bootstrap Version: 5.3(1)
Hardware Version: 2.0 Model: WS-C6509 Serial #: xxxxxxxx
Mod Port Model Serial # Versions
--- ---- ------------------- -----------
--------------------------------------
1 2 WS-X6K-SUP1A-2GE SAD043301GL Hw : 3.2
Fw : 5.3(1)
Fw1: 5.1(1)CSX
Sw : 5.5(1)
Sw1: 5.5(1)
L3 Switching Engine SAD04330MCS Hw : 1.1
3 8 WS-X6408A-GBIC SAL0541D4W4 Hw : 2.0
Fw : 5.4(2)
Sw : 5.5(1)
5 8 WS-X6408A-GBIC SAL0533AFND Hw : 2.0
Fw : 5.4(2)
Sw : 5.5(1)
15 1 WS-F6K-MSFC SAD04281AW3 Hw : 1.4
Fw : 12.1(1)E,
Sw : 12.1(1)E,
DRAM FLASH
NVRAM
Module Total Used Free Total Used Free
Total Used Free
------ ------- ------- ------- ------- ------- -------
----- ----- -----
1 65408K 38426K 26982K 16384K 6925K 9459K
512K 211K 301K
Uptime is 19 day, 6 hours, 56 minutes
C65SV-1 (enable) set spantree ?
backbonefast Enable or disable fast
convergence
disable Disable spanning tree
enable Enable spanning tree
fwddelay Set spantree forward delay
hello Set spantree hello interval
maxage Set spantree max aging time
portcost Set spantree port cost
portfast Set spantree port fast start
portpri Set spantree port priority
portvlancost Set spantree port cost per
vlan
portvlanpri Set spantree port vlan
priority
priority Set spantree priority
root Set switch as primary or
secondary root
uplinkfast Enable or disable uplinkfast
groups
C65SV-1 (enable) set spantree ?
This archive was generated by hypermail 2.1.4 : Wed Jun 02 2004 - 11:12:19 GMT-3