From: wing_lam@jossynergy.com
Date: Wed Dec 08 2004 - 07:20:04 GMT-3
Hi,
I have also meet a case, that several of the LAN devices replies. If then,
what makes the remaining not replies?
Thanks,
Winglam
Lee Donald
<Lee.Donald@t-sys To: wing_lam@jossynergy.com
tems.co.uk> cc:
Subject: RE: Can anybody explain why
12/08/2004 06:17
PM
It's first to receive the broadcast.
-----Original Message-----
From: wing_lam@jossynergy.com [mailto:wing_lam@jossynergy.com]
Sent: 08 December 2004 10:15
To: Hoonpongsimanont, Chalermchai
Cc: ccielab@groupstudy.com; nobody@groupstudy.com
Subject: RE: Can anybody explain why
Hi,
But why when 10.1.1.40 replies, the multi-layer switch not capturing it's
source MAC address?
Also, what device will reply to 10.1.255.255? I have a lot of devices here
but why only this replies?
Thanks,
BBD
|---------+--------------------------------------------->
| | "Hoonpongsimanont, Chalermchai" |
| | <chalermchai.hoonpongsimanont@atos|
| | origin.com> |
| | Sent by: nobody@groupstudy.com |
| | |
| | |
| | 12/08/2004 05:45 PM |
| | Please respond to |
| | "Hoonpongsimanont, Chalermchai" |
| | |
|---------+--------------------------------------------->
>---------------------------------------------------------------------------
-------------------|
|
|
| To: wing_lam@jossynergy.com, ccielab@groupstudy.com
|
| cc:
|
| Subject: RE: Can anybody explain why
|
>---------------------------------------------------------------------------
-------------------|
Hi,
I think this is because router did not send out arp request for the
broadcast IP address. It already know MAC address for broadcast, right?
When ICMP echo packets were sent out to broadcast address, router just
encapsulated them with destination mac address as broadcast.
But if you show on 10.1.1.40, you will see arp entry for 10.1.0.100. This
is
because when 10.1.1.40 sent back echo reply, it unicast to 10.1.0.100.
Hope this help,
David
-----Original Message-----
From: wing_lam@jossynergy.com [mailto:wing_lam@jossynergy.com]
Sent: Wednesday, December 08, 2004 4:20 PM
To: ccielab@groupstudy.com
Subject: Can anybody explain why
Hi Group,
I am try pinging the broadcast on a network, with only 1 device replies.
But I cannot see it's arp, why?
Router#p 10.1.255.255
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.255.255, timeout is 2 seconds:
.
Reply to request 1 from 10.1.1.40, 33 ms
Reply to request 2 from 10.1.1.40, 8 ms
Reply to request 3 from 10.1.1.40, 9 ms
Reply to request 4 from 10.1.1.40, 9 ms
Router#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.1.0.100 - 000f.2406.7840 ARPA Vlan1
Internet 10.1.0.1 0 0008.027f.da1d ARPA Vlan1
Internet 10.1.1.1 0 000f.fe14.dc61 ARPA Vlan1
Router#sh run int vlan 1
Building configuration...
Current configuration : 60 bytes
!
interface Vlan1
ip address 10.1.0.100 255.255.0.0
end
Thanks,
BBD
DISCLAIMER:- This email is confidential and intended only for the use of
the individual or entity named above and may contain information that is
privileged. If you are not the intended recipient, you are notified that
any dissemination, distribution or copying of this email is strictly
prohibited. If you have received this email in error, please notify us
immediately by return email or telephone and destroy the original message.
Thank you.
This archive was generated by hypermail 2.1.4 : Mon Jan 03 2005 - 10:31:25 GMT-3