From: Nancy Keating (nlk2004@yahoo.com)
Date: Mon Jul 18 2005 - 14:05:40 GMT-3
I agree that your configuration is correct.
The documentation, IPExpert Version 7.0, section 3,
page 46, which states:
"If you have a number of frame realy map statements on
a physical or multipoint interface and you type a
frame relay interface-dlci statement referring to the
same dlci that the map stements were referencing, all
of the map stements will be erased."
is incorrect.
Nancy
--- Montiean <noktes@bellsouth.net> wrote:
> This made the question in my head again that I miss
> something or not,
> because I don't see the problem in my configuration.
>
> show run int s0/0
> Building configuration...
>
> Current configuration : 418 bytes
> !
> interface Serial0/0
> ip address 10.110.110.6 255.255.255.0
> encapsulation frame-relay IETF
> ip ospf network point-to-multipoint
> no fair-queue
> frame-relay traffic-shaping
> frame-relay map ip 10.110.110.4 604 broadcast
> frame-relay map ip 10.110.110.7 607 broadcast
> frame-relay interface-dlci 604
> class 64k
> frame-relay interface-dlci 607
> class 32k
> no frame-relay inverse-arp
> frame-relay lmi-type cisco
> end
>
> r6#show run map
> Building configuration...
>
> Current configuration:
> !
> map-class frame-relay 64k
> frame-relay cir 64000
> frame-relay bc 8000
> frame-relay adaptive-shaping becn
> !
> map-class frame-relay 32k
> frame-relay cir 32000
> frame-relay bc 4000
> end
>
> r6#sho traff
>
> Interface Se0/0
> Access Target Byte Sustain Excess
> Interval Increment Adapt
> VC List Rate Limit bits/int bits/int
> (ms) (bytes)
> Active
> 607 32000 500 4000 0
> 125 500 -
> 604 64000 1000 8000 0
> 125 1000 BECN
> r6#ping 10.110.110.4
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 10.110.110.4,
> timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 4/4/8 ms
> r6#ping 10.110.110.7
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 10.110.110.7,
> timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 32/33/36 ms
>
>
> Hmm!!! I have to go back to read frame-relay agian.
> Someone correct me if I
> miss something
>
> -- Montiean
>
> ----- Original Message -----
> From: "Nancy Keating" <nlk2004@yahoo.com>
> To: <ccielab@groupstudy.com>
> Sent: Monday, July 18, 2005 8:59 AM
> Subject: traffic shaping for one dlci on a physical
> interface
>
>
> > If I have a physical interface configured for
> frame
> > relay with multiple map and dlci's configured and
> i
> > want to traffic shape just one dlci, how is this
> > accomplished?
> >
> > I thought I would want to use the frame
> interface-dlci
> > command with the map command; however IPExpert
> Section
> > 3 of Version 7.0 says that you cannot use map and
> > interface-dlci on the same interface.
> >
> > Thank you
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam? Yahoo! Mail has the best spam
> protection around
> > http://mail.yahoo.com
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:00:30 GMT-3