Hi Jeremie
Can we get a sh int on each of the 4 interfaces involved with them all up?
Have you done any debugging?
-
On Tue, Jul 28, 2009 at 7:34 PM, Ananfack, Jeremie N <
jeremie_n_ananfack_at_fanniemae.com> wrote:
> It is not a cabling issue.
> When I shut both g1/5 and g4/15 down, the port to be first unshut will
> stay up and the second will stay down.
> Right now, g4/15 is up and g1/5 down.
>
>
> ________________________________
>
> From: joshua atterbury [mailto:joshuaatterbury_at_gmail.com]
> Sent: Tuesday, July 28, 2009 6:15 PM
> To: Ananfack, Jeremie N
> Cc: Joe Astorino; ccielab_at_groupstudy.com
> Subject: Re: Port Channel not coming up
>
>
> have you confirmed that it is not a cabling problem? Ie is you make
> gi4/15 an access port and do the same for the other end does it come up?
>
>
> On Wed, Jul 29, 2009 at 4:44 AM, Ananfack, Jeremie N
> <jeremie_n_ananfack_at_fanniemae.com> wrote:
>
>
>        The logical interface is already up.
>        I was expecting a 2Gig interface and both g1/5 & g4/15 as
> members of the
>        channel.
>        Still unable to bring up g4/15.
>
>
>        rp01#sh int po3
>
>        Port-channel3 is up, line protocol is up (connected)
>
>         Hardware is EtherChannel, address is 00d0.c0d6.4fd2 (bia
>        00d0.c0d6.4fd2)
>         MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
>            reliability 255/255, txload 1/255, rxload 1/255
>         Encapsulation ARPA, loopback not set
>         Keepalive set (10 sec)
>         Full-duplex, 1000Mb/s
>         input flow-control is off, output flow-control is off
>
>         Members in this channel: Gi1/5
>
>         ARP type: ARPA, ARP Timeout 04:00:00
>
>
>        ________________________________
>
>        From: Joe Astorino [mailto:jastorino_at_ipexpert.com]
>        Sent: Tuesday, July 28, 2009 1:48 PM
>        To: Ananfack, Jeremie N
>        Cc: ccielab_at_groupstudy.com
>        Subject: Re: Port Channel not coming up
>
>
>
>        Allow the native VLAN on the trunks of the physical and logical
>        interfaces.
>
>
>        On Tue, Jul 28, 2009 at 12:01 PM, Ananfack, Jeremie N
>        <jeremie_n_ananfack_at_fanniemae.com> wrote:
>
>
>               Hello,
>
>               Any suggestion as far as bringing this port channel up?
>               The port channel interface is up but the other member of
> the
>        channel is
>               down and doesn't show as a member of that channel.
>
>
>               sw1
>               interface GigabitEthernet1/5
>               GigabitEthernet1/5 is up, line protocol is up (connected)
>                description 1sharebc-sp01a
>                switchport
>                switchport trunk encapsulation dot1q
>                switchport trunk native vlan 601
>                switchport trunk allowed vlan none
>                switchport mode trunk
>                no ip address
>                no snmp trap link-status
>                channel-group 3 mode desirable non-silent
>               !
>
>               interface GigabitEthernet4/15
>               GigabitEthernet4/15 is up, line protocol is down
> (notconnect)
>                description 1sharebc-sp01a
>                switchport
>                switchport trunk encapsulation dot1q
>                switchport trunk native vlan 601
>                switchport trunk allowed vlan none
>                switchport mode trunk
>                no ip address
>                no snmp trap link-status
>                channel-group 3 mode desirable non-silent
>               !
>
>               interface Port-channel3
>               Port-channel3 is up, line protocol is up (connected)
>                description 1sharebc-sp01a
>               Members in this channel: Gi1/5
>                switchport
>                switchport trunk encapsulation dot1q
>                switchport trunk native vlan 601
>                switchport trunk allowed vlan none
>                switchport mode trunk
>                no ip address
>
>
> ==========================================================
>
>               sw2
>               set vlan 601  9/5-6
>               clear trunk 9/5  1-4094
>               set trunk 9/5  on dot1q
>               clear trunk 9/6  1-4094
>               set trunk 9/6  on dot1q
>               set spantree portfast    9/5-8 disable
>               set port channel 9/5-6 mode desirable non-silent
>
>
>               Blogs and organic groups at http://www.ccie.net
>
>
>
> _______________________________________________________________________
>               Subscription information may be found at:
>               http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>
>
>
>
>
>        --
>        Regards,
>
>        Joe Astorino - CCIE #24347 R&S
>        Technical Instructor - IPexpert, Inc.
>        Cell: +1.586.212.6107
>        Fax: +1.810.454.0130
>        Mailto:  jastorino_at_ipexpert.com
>
>
>        Blogs and organic groups at http://www.ccie.net
>
>
> _______________________________________________________________________
>        Subscription information may be found at:
>        http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>
-- --- Brian Dooley Technical Consultant II CCIE # 23688 AT&T WCS - BFS Field Operations - Southeast morinack_at_gmail.com "Fall seven times, stand up eight." -- Japanese Proverb Blogs and organic groups at http://www.ccie.netReceived on Tue Jul 28 2009 - 20:36:31 ART
This archive was generated by hypermail 2.2.0 : Sat Aug 01 2009 - 13:10:23 ART