Re: VLAN-based EoMPLS

check to make sure LDP (not targeted) works ok and that you have a label to
reach the remote PE loopback address.

On 27 October 2010 13:24, Manaf Al Oqlah <manafo_at_hotmail.com> wrote:

> ########### PE01 ###########
>
> PE01#sh mpls l2transport vc detail
> Local interface: Vl100 up, line protocol up, Eth VLAN 100 up
> Interworking type is Ethernet
> Destination address: 2.2.2.2, VC ID: 100, VC status: up
> Output interface: Gi1/1/1, imposed label stack {18}
> Preferred path: not configured
> Default path: active
> Next hop: 10.0.0.2
> Create time: 00:22:03, last status change time: 00:07:53
> Signaling protocol: LDP, peer 2.2.2.2:0 up
> Targeted Hello: 1.1.1.1(LDP Id) -> 2.2.2.2
> Status TLV support (local/remote) : enabled/not supported
> Label/status state machine : established, LruRru
> Last local dataplane status rcvd: no fault
> Last local SSS circuit status rcvd: no fault
> Last local SSS circuit status sent: no fault
> Last local LDP TLV status sent: no fault
> Last remote LDP TLV status rcvd: not sent
> MPLS VC labels: local 20, remote 18
> Group ID: local 0, remote 0
> MTU: local 1900, remote 1900
> Remote interface description:
> Sequencing: receive disabled, send disabled
> VC statistics:
> packet totals: receive 0, send 5
> byte totals: receive 0, send 630
> packet drops: receive 0, send 0
>
> PE01#sh run int g1/1/2
> Building configuration...
>
> Current configuration : 128 bytes
> !
> interface GigabitEthernet1/1/2
> description To CE01
> switchport access vlan 100
> switchport mode access
> speed auto 1000
> end
>
> ###### PE02 ############
>
> PE02#sh mpls l2transport vc detail
> Local interface: Vl100 up, line protocol up, Eth VLAN 100 up
> Interworking type is Ethernet
> Destination address: 1.1.1.1, VC ID: 100, VC status: up
> Output interface: Gi1/1/1, imposed label stack {20}
> Preferred path: not configured
> Default path: active
> Next hop: 10.0.0.1
> Create time: 00:21:35, last status change time: 00:09:38
> Signaling protocol: LDP, peer 1.1.1.1:0 up
> Targeted Hello: 2.2.2.2(LDP Id) -> 1.1.1.1
> Status TLV support (local/remote) : enabled/not supported
> Label/status state machine : established, LruRru
> Last local dataplane status rcvd: no fault
> Last local SSS circuit status rcvd: no fault
> Last local SSS circuit status sent: no fault
> Last local LDP TLV status sent: no fault
> Last remote LDP TLV status rcvd: not sent
> MPLS VC labels: local 18, remote 20
> Group ID: local 0, remote 0
> MTU: local 1900, remote 1900
> Remote interface description:
> Sequencing: receive disabled, send disabled
> VC statistics:
> packet totals: receive 5, send 0
> byte totals: receive 540, send 0
> packet drops: receive 0, send 0
>
> PE02#sh run int g1/1/2
> Building configuration...
>
> Current configuration : 128 bytes
> !
> interface GigabitEthernet1/1/2
> description to CE01
> switchport access vlan 100
> switchport mode access
> speed auto 1000
> end
>
> ########### CE01 ############
>
> CE01#sh run int g1/0/25
> interface GigabitEthernet1/0/25
> description to PE01
> switchport access vlan 100
> switchport mode access
> end
> !
> CE01#sh run int vlan 100
> interface Vlan100
> ip address 192.168.0.1 255.255.255.0
>
> ######### CE02 ###########
>
> CE02#sh run int g1/1/1
> interface GigabitEthernet1/1/1
> description to PE02
> switchport access vlan 100
> switchport mode access
> speed auto 1000
> end
>
> CE02#sh run int vlan 100
> interface Vlan100
> ip address 192.168.0.2 255.255.255.0
>
>
>
>
>
>
> From: srinivas pv
> Sent: Wednesday, October 27, 2010 2:42 PM
> To: Manaf Al Oqlah
> Cc: Group Study
> Subject: Re: VLAN-based EoMPLS
>
>
> Hi,
>
>
> Could you give following details
>
>
> On both PEs:
> show mpls l2 vc detail
> sh run int <int connected to CE>
>
>
> On both CEs:
> sh run int <int connected to PE>
>
>
> Thanks,
> Srinivas
>
>
>
> On Wed, Oct 27, 2010 at 5:00 PM, Manaf Al Oqlah <manafo_at_hotmail.com>
> wrote:
>
> Hi,
>
> I have established an EoMPLS circuit on ME3750 switches as below.
> everything
> seems to be working fine as my virtual circuit is UP
> but my problem is that I cant ping IP address CE02 from CE01
>
> PC01---CE01---PE01---PE02---CE02---PC02
>
> I have applied the following configuration on PE01 & PE02 ES ports
>
> interface loopback 0
> ip address 1.1.1.1 255.255.255.255
> !
> interface GigabitEthernet1/1/1
> description to PE02
> ip address 10.0.0.1 255.255.255.252
> mpls ip
> !
> interface GigabitEthernet1/1/2
> description to CE01
> switchport mode access
> switchport access vlan 100
> !
> vlan 100
> !
> interface vlan 100
> xconnect 2.2.2.2 100 encapsulation mpls
>
> where could me my problem!
>
> Regards,
> Manaf Al Oqlah
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Oct 27 2010 - 14:12:45 ART