Re: OER master active-probe

From what I hdvh seen....

I would say it is a Must to put set mode monitor active under oer-map for
particular prefix

Vijaya

Sent from my %brant0
On Apr 22, 2012 4:34 PM, "marc edwards" <renorider_at_gmail.com> wrote:

> Problem was I didn't have an oer-map that matched the prefix. Any
> active probe will need oer map....? please confirm or correct this
> statement.
>
> R6#sh run | b ^oer-map
> oer-map prfx 10
> match traffic-class prefix-list prfx
>
> R6#sh oer master active-probes
> OER Master Controller active-probes
> Border = Border Router running this Probe
> State = Un/Assigned to a Prefix
> Prefix = Probe is assigned to this Prefix
> Type = Probe Type
> Target = Target Address
> TPort = Target Port
> How = Was the probe Learned or Configured
> N - Not applicable
>
> The following Probes exist:
>
> State Prefix Type Target TPort How
> Codec
> Assigned 3.3.3.3/32 echo 3.3.3.3 N Cfgd
> N
>
> The following Probes are running:
>
> Border State Prefix Type Target TPort
> 1.1.1.6 ACTIVE 3.3.3.3/32 echo 3.3.3.3 N
>
>
> Thanks,
> Marc
>
> On Sun, Apr 22, 2012 at 1:16 PM, marc edwards <renorider_at_gmail.com> wrote:
> > Experts,
> >
> > I am running through a lab on OER. When I look at the sh oer master
> > active-probe output on my rack I see:
> > ----
> > R6#sh oer master active-probes
> > OER Master Controller active-probes
> > Border = Border Router running this Probe
> > State = Un/Assigned to a Prefix
> > Prefix = Probe is assigned to this Prefix
> > Type = Probe Type
> > Target = Target Address
> > TPort = Target Port
> > How = Was the probe Learned or Configured
> > N - Not applicable
> >
> > The following Probes exist:
> >
> > State Prefix Type Target TPort How
> Codec
> > Unassigned echo 3.3.3.3 N Cfgd
> N
> >
> > The following Probes are running:
> >
> > Border State Prefix Type Target
> TPort
> > ----
> > When I look at answer key it shows:
> > ---
> > OER Master Controller active-probes
> > Border = Border Router running this Probe
> > = Probe is assigned to this Prefix
> > State = Un/Assigned to a Prefix
> > Prefix
> >
> > Type = Probe Type
> > Target = Target Address
> > TPort = Target Port
> > llowing Probes exist:
> > tate Prefix
> >
> > S
> > How = Was the probe Learned or Configured
> > N - Not applicable
> >
> > The
> > f
> > o Type Target TPort How
> > Assigned 3.3.3.3/32 echo 3.3.3.3 N Cfgd
> > The following Probes are running:
> >
> > Border State Prefix Type Target TPo
> > r1.1.1.6 ACTIVE 3.3.3.3/32 echo 3.3.3.3
> N
> > ----
> >
> > Any ideas why my state is unassigned? Here is configuration from router
> >
> >
> > R6#sh run | b ^oer
> >
> > oer master
> > policy-rules prfx
> > logging
> > !
> > border 1.1.1.6 key-chain OER
> > interface Serial0/0/0.62 external
> > interface FastEthernet0/1 external
> > interface FastEthernet0/0 internal
> > !
> > learn
> > delay
> > periodic-interval 3
> > monitor-period 1
> > no max range receive
> > mode route control
> > mode monitor active
> > !
> > active-probe echo 3.3.3.3
> > !
> > oer border
> > logging
> > local FastEthernet0/0
> > master 1.1.1.6 key-chain OER
> > !
> > ip prefix-list prfx seq 5 permit 3.3.3.3/32
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Sun Apr 22 2012 - 16:38:36 ART