Re: Image verification

The Pitonisa says to check your memory requirements. Also, she needs to
see the console log of a rebload sequence, that would help uncover the
mood of the gods in your switching quadrant...

Imran Ali @ 04/11/2013 10:55 -0300 dixit:
> thanks for reply but why my boot command is not working and it is
> always booting with first image ..
>
>
> On Mon, Nov 4, 2013 at 2:10 PM, Antonio Soares <amsoares_at_netcabo.pt> wrote:
>
>> Use the verify /md5 to be completely sure.
>>
>> By default the 4500's have confreg=2101, you need to change it to 2102.
>>
>>
>>
>> Regards,
>>
>> Antonio Soares, CCIE #18473 (R&S/SP)
>> amsoares_at_netcabo.pt
>> http://www.ccie18473.net
>>
>>
>> -----Original Message-----
>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
>> Imran Ali
>> Sent: segunda-feira, 4 de Novembro de 2013 06:32
>> To: Cisco certification
>> Subject: OT: Image verification
>>
>> Hi all
>>
>> i have uploaded an image and i have done verification .
>>
>> core1#verify cat4500-entservicesk9-mz.122-54.SG1.bin
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>>
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> C
>> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
>> Verified cat4500-entservicesk9-mz.122-54.SG1.bin
>> SV-TS202-BB1#
>>
>>
>> 1) what does this verification mean ? does it mean that checksum is
>> ok ?
>>
>> or is it safe now to delete old image and reload so that it
>> boots with this image.
>>
>> this is cat4506..
>>
>>
>>
>> 2) i have tried to set boot preference to new image ..but still it is
>> booting with old image ..
>> core1#show run | in boot
>> boot system flash bootflash:cat4500-entservicesk9-mz.122-54.SG1.bin
>>
>> the issue is boot command is excepting any thing i type and not verifying
>> its syntax..
>>
>> core1(config)#boot system flash abc
>> core1(config)#
>>
>>
>> what is the correct syntax .
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>

-- 
Carlos G Mendioroz  <tron_at_huapi.ba.ar>  LW7 EQI  Argentina
Blogs and organic groups at http://www.ccie.net